Hantek DSO5102P USB Digital Storage Oscilloscope 2Channels 100MHz 1GSa/s
Hantek DSO5102P USB Digital Storage Oscilloscope 2Chan... $408.51

Description:   Hantek DSO5102P USB Digital Storage Oscilloscope 2Channels 100MHz 1GSa/s   Features:    100MHz bandwidths 1GSa/s Real Time sample rate Large (7.0-inch) color display,WVGA(800x480) Record length up to 40K Trigger mode: edge/pulse width/line selectable video/slop/overtime etc. USB host and device connectivity, standard Multiple automatic measurements Four math functions, including FFTs standard Provides software for PC real-time analysis    Specification:     Model DSO5202P DSO5102P DSO5072P Acquisition Sample Rate  Real-Time Sample: 1GS/s Equivalent Sample: 25GS/s Acquisition Modes       Normal Normal data only Pea'k Detect High-frequency and randon glith capture Average Wavefom Average, selectable 4,8,16,32,64,128 Inputs Inputs Coupling AC, DC, GND Inpits Impendance 1MΩ±2% II20pF±3pF Probe Attenuation 1X, 10X Supported Probe Attenuation Factor 1X, 10X, 100X, 1000X Maximum Input Voltage CAT I and CAT II: 300VRMS (10×), Installation Category; CAT III: 150VRMS (1×); Installation Category II: derate at 20dB/decade above 100kHz to 13V Pea'k AC at 3MHz* and above.  For non-sinusoidal waveforms, Pea'k value must be less than 450V.  Excursion above 300V should be of less than 100ms duration.  RMS signal level including all DC components removed through AC coupling must be limited to 300V.  If these values are exceeded, damage to the oscilloscope may occur. Horizontal Sample Rate Range 500MS/s--1GS/s Waveform Interpolation (sin x)/x R'ecord Length 40'K SEC/DIV Range 4ns/div to 40s/div 4ns/div to 40s/div Sample Rate and Delay Time Accuracy ±50ppm(at over any ≥1ms time interval) Position Range 2ns/div to 10ns/div;  (-4div x s/div) to 20ms; 20ns/div to 80us/div; (-8div x s/div) to 40ms; 200us/div to 40s/div; (-8div x s/div) to 400s Incremental  Time Measurement Accuracy  (Full Bandwidth) Single-shot, Normal mode:± (1 sample interval +100ppm × reading + 0.6ns); >16 averages:± (1 sample interval + 100ppm × reading + 0.4ns); Sample interval = s/div ÷ 200 Vertical Vertical Resolution 8-bit resolution, all channel sampled simultaneously Position Range 2mV/div to 200mV/div, ±2V 200mV/div to 5V/div, ±50V Bandwidth 100MHz 100MHz 70MHz Rise Time at BNC( typical) 3.5ns  3.5ns 5ns Analog Bandwidth in Normal and  Average modes at BNC or with probe, DC Coupled 2mV/div to 20mV/div, ±400mV;  50mV/div to 200mV/div, ±2V 500mV/div to 2V/div, ±40V; 5V/div, ±50V Math +, -, *, /, FFT FFT Windows: Hanning, Flatop, Rectamgular, Bartlett, Blackman; 1024 sample point Bandwidth Limit 20MHz Low Frequency Response (-3db) ≤10Hz at BNC DC Gain Accuracy ±3% for Normal or Average acquisition mode, 5V/div to 10mV/div; ±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div DC Measurement Accuracy,  Average Acquisition Mode When vertical displacement is zero, and N ≥16:± (3% × reading + 0.1div + 1mV) only 10mV/div or greater is selected;  When vertical displacement is not zero, and N≥16: ± [3% × (reading + vertical position) + 1% of vertical position + 0.2div];  Add 2mV for settings from 2mV/div to 200mV/div; add 50mV for settings from 200mV/div to 5V/div Volts Measurement Repeatability,  Average Acquisition Mode D1elta volts between any two averages of ≥16 waveforms acquired under same setup and ambient conditions Trigger System Trigger Types Edge, Video, Pulse, Slope, Over time, Alternative Trigger Source CH1, CH2, EXT, EXT/5, AC Line Trigger Modes Auto, Normal, Single Coupling Type DC, AC, Noise Reject, HF Reject, LF Reject Trigger Sensitivity (Edge Trigger Type) DC(CH1,CH2): 1div from DC to 10MHz; 1.5div from 10MHz to 100MHz; 2div from 100MHz to Full; DC(EXT):  200mV from DC to 100MHz; 350mV from 100MHz to 200MHz; DC(EXT/5):        1V from DC to 100MHz;1.75V from 100MHz to 200MHz;        AC: Attenuates signals below 10Hz; HF Reject: Attenuates signals above 80kHz;  LF Reject: Same as the DC-coupled limits for frequencies above 150kHz; attenuates signals below 150kHz Trigger Level Range CH1/CH2: ±8 divisions from center of screen;  EXT: ±1.2V; EXT/5:±6V Trigger Level Accuracy( typical)Accuracy  is for signals having rise and fall times ≥20ns CH1/CH2: 0.2div × volts/div within ±4 divisions from center of screen; EXT: ± (6% of setting + 40mV); EXT/5: ± (6% of setting + 200mV); Set Level to 50%(typical) Operates with input signals ≥50Hz Video Trigger   Video Trigger Type  CH1, CH2: Pea'k-to-Pea'k amplitude of 2 divisions; EXT: 400mV; EXT/5: 2V Signal Formats and Field Rates, Video Trigger Type Supports NTSC, PAL and SECAM broadcast systems for any field or any line Holdoff Range 100ns ~ 10s Pulse Width Trigger   Pulse Width Trigger Mode Trigger when (< , >, = , or ≠); Positive pulse or Negative pulse Pulse Width Trigger Point Equal: The oscilloscope triggers when the trailing edge of the pulse crosses the trigger level. Not Equal: If the pulse is narrower than the specified width, the trigger point is the trailing edge. Otherwise, the oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width. Less than: The trigger point is the trailing edge. Greater than (also called overtime trigger): The oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width Pulse Width Range 20ns ~ 10s Slope Trigger   Slope Trigger Mode Trigger when (< , > , = , or ≠ ); Positive slope or Negative slope Slope Trigger Point Equal: The oscilloscope triggers when the waveform slope is equal to the set slope. Not Equal: The oscilloscope triggers when the waveform slope is not equal to the set slope. Less than: The oscilloscope triggers when the waveform slope is less than the set slope. Greater than: The oscilloscope triggers when the waveform slope is greater than the set slope. Time Range 20ns ~ 10s Overtime Trigger   Over Time Mode Rising edge or Falling edge Time Range 20ns ~ 10s Alternative Trigger   Trigger on CH1 Internal Trigger: Edge, Pulse Width, Video, Slope Trigger on CH2 Internal Trigger: Edge, Pulse Width, Video, Slope Trigger Frequency Counter Readout Resolution 6 digits Accuracy (typical) ±30ppm (including all frequency reference errors and ±1 count errors) Frequency Range AC coupled, from 4Hz Min to rated bandwidth Signal Source Pulse Width or Edge Trigger modes: all available trigger sources The Frequency Counter measures trigger source at all times, including when the oscilloscope acquisition pauses  due to changes in the run status, or acquisition of a single shot event has completed. Pulse Width Trigger mode: The oscilloscope counts pulses of significant magnitude inside the 1s measurement window that qualify as triggerable events,  such as narrow pulses in a PWM pulse train if set to < mode and the width is set to a relatively small time. Edge Trigger mode: The oscilloscope counts all edges of sufficient magnitude and correct polarity. Video Trigger mode: The Frequency Counter does not work. Measure Cursor Measurement Voltage difference between cursors: ΔV Time difference between cursors: ΔT Reciprocal of ΔT in Hertz (1/ΔT) Auto Measuerment Frequency, Period, Mean, Pk-Pk, Cycli RMS, Min, Maximum, Rise time, Fall Time, +Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty, Vbase, Vtop, Vmid, Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS, FOVShoot, RPREShoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF Display Display Type 7 inch 64K color TFT (diagonal liquid crystal) Display Resolution 800 horizontal by 480 vertical pixels Display Contrast Adjustable (16 gears) with the progress bar Probe Compensator Output Output Voltage( typical) About 5Vpp into ≥1MΩ load Frequency(typical) 1kHz Power Supply Supply Voltage 100-120VACRMS(±10%), 45Hz to 440Hz, CATII 120-240VACRMS(±10%), 45Hz to 66Hz, CATII Power Consumption <30W Fuse 2A, T rating, 250V Environmental Temperature Operating: 32F to 122F (0C to 50C); Nonoperating: -40F to 159.8F (-40C to +71C) Cooling Method Convection Humidity +104F or below (+40C or below): ≤90% relative humidity; 106F to 122F (+41C to 50C): ≤60% relative humidity Altitude Operating: Below 3,000m (10,000 feet); Nonoperaring: Below 15,000m(50,000 feet) Mechanical Size Length 385mm, Width 200mm, Height 245mm Weight 3.5KG(with Packing);  2.08KG(without Packing) Package includes:    1 x Digital Storage Oscilloscope 2 x Probes (PP150) 1 x Oscilloscope Power Cable 1 x USB line 1 x Hantek data CD 1 x Manufacturer Certificate Details pictures:                 

Hantek 3in1 Digital Oscilloscope+Waveform Generator+Multimeter Portable USB 2 Channels 40mhz 70mhz LCD Display Test Meter Tools Ultra-low Power Design With Large-capacity lithium Battery One-key AUTO
Hantek 3in1 Digital Oscilloscope+Waveform Generator+Mu... from $201.54

Overview:   Digital oscilloscope + waveform generator + multimeter, all in one! AUTO one-key test + cursor measurement function! Output sine, square, triangle, trapezoidal and other waveforms output! 4000 counts universal multimeter function! A real professional and magic scope! buy one and no need buy more equipments!   Features: ♦ Oscilloscope + Waveform Generator + Multimeter: This multi-purpose station own three universal test instrument functions. It is outgoing right-hand product for engineers. ♦ Intelligent charging control: Its lithium batteries can be recharged byeither high current-5V/2A or ordinary computer USB interface. Allow while charging, while using, very convenient and handy; ♦ Ultra-low power design: Type C charging interface, after every recharge of 2 hours, the device can be used continuously for a full day or standby more than two months; ♦ Large-capacity lithium battery power supply: Tesla style 18650 replaceable lithium battery power system, free from replace battery; ♦ 5V/2A charger + Type C charging cable: Type C power + data transfer interface, can share the charger and data cable with your mobile phone; ♦ AUTO one-key test: Magic tool and essential function for test newbie; ♦ Volume small, one hand holding: The 45 degree suspension bracket design provide you a work station anywhere anytime; ♦ One key page out, quick compare two groups of reference waveforms + 6 groups of waveforms storage, simple and effective; ♦ Digital voltmeter function: automatic frequency and amplitude measurement, convenient and worry-free; ♦ Its cursor measurement function supports time and voltage manual measurement, and measure the required waveforms accurately; ♦ Color LCD screen: exquisite and smooth lines make the waveforms clear and undistorted when magnify; ♦ Minimalist keyboard design simplify operation, convenient to use; ♦ Unibody casing: fine touch feeling, favorable impact resistance, outstanding heat resistance, easy to disassemble; ♦ Self-calibration function: free from level drift after long time unused; ♦ Universal multimeter function: voltage, current, resistance, diode, capacitor, on-off test; ♦ Waveform generator output function: output sine, square, triangle, trapezoidal and other waveforms; sine up to 25MHz; Model Channel Bandwidth Sample Power DMM AFG Hantek2C42 2 CH+DMM (Oscilloscope+Multimeter ) 40MHz 250MSa/S Direct charge √ - Hantek2C72 2 CH+DMM (Oscilloscope+Multimeter) 70MHz 250MSa/S Direct charge √ - Hantek2D42 2 CH+AFG+DMM (Oscilloscope+Waveform Generator+Multimeter ) 40MHz 250MSa/S Direct charge √ √ Hantek2D72 2 CH+AFG+DMM (Oscilloscope+Waveform Generator+Multimeter) 70MHz 250MSa/S Direct charge √ √ >>Please Click Here to Download the English User Manual and Software << Package Includes: 1 x Digital Oscilloscope 1 x Probe 2 x Clip Probe 1 x Charging cable 1 x Power adapter 1 x Multimeter Probe Note: We will send you a plug adapter according to your country. The 2C42 and 27C2 only include the oscilloscope + Multimeter function, and the 2D42 and 2D72 include the Oscilloscope + Multimeter + Waveform Generator. Please confirm that the the model you want is been selected correctlu before purchasing.  New Arrival Recommendation!!!                              Hantek TO11/TO22 Digital LCR Meter Portable Handheld Inductance Capacitance Resistance Measurement Tester                           id: 1604498                                                                              Details pictures:

DANIU ADS1013D 2 Channels 100MHz Band Width 1GSa/s Sampling Rate Oscilloscope with 7 Inch Color TFT LCD Touch Screen
DANIU ADS1013D 2 Channels 100MHz Band Width 1GSa/s Sam... $247.78

Description:   ADS1013D is a full-featured, highly practical, cost-effective dual-channel flat-panel oscilloscope launched by DANIU for the maintenance and R & D industry; this oscilloscope has a real-time sampling rate of 1GSa / s and an analog bandwidth of 100MHz * 2. With complete trigger function (single / normal / automatic), it can be used freely for periodic analog signals or non-periodic digital signals; the built-in high-voltage protection module can tolerate a continuous voltage of up to 400V . Oscilloscope burnout accident caused by the probe being turned to the 10X position. Large time base scroll mode can monitor slow level changes; Equipped with highly efficient one-key AUTO, which can display the measured waveform without tedious adjustments; the display is equipped with a 7-inch 800 * 480 resolution high-definition LCD LCD screen, and the operation method is capacitor Screen touch + gesture operation, extremely convenient; cursor measurement function, you do not need to read the backg round scale unit and quantity when manually reading the amplitude and frequency parameters, and you can directly get the peak, peak and frequency without conversion; extremely convenient screenshot And waveform storage function, built-in 1GB storage space, can store up to 1000 screenshots + 1000 sets of waveform data, the storage process is simple and fast, save the current waveform anytime, anywhere with a single touch, no cumbersome prompts and choices, keep calm The current data is saved in the place, which is very convenient; the powerful waveform picture manager supports thumbnail browsing, viewing, detailed viewing, page turning, deletion and waveform zooming in, zooming out, moving, etc., to facilitate secondary analysis. The fuselage is equipped with a USB interface, which can be connected to a computer to share its screenshots with the computer, which is convenient for secondary analysis; Lissajous figures graphic display function can be used to determine the amplitude, freque ncy, and phase contrast of two groups of signals; Analysis of the harmonic components of the signal; built-in 6000mah high-quality lithium battery, which can last for 4 hours on a full charge, and can be used while charging like a notebook Features:   1 : Intelligent anti-burn , 1X Can withstand up to 400V withstand voltage 2 : 100MHz analog bandwidth @ 1GSa/s sampling rate ( 1X = 5MHz , 10X = 100MHz ) 3 : Fully fit 7 inch 800 * 480 resolution color TFT LCD display with bright colors and high contrast 4 : Capacitive touch screen, the same as the touch mode of modern mobile smart phone, is not a resistive touch screen with ancient nail operation 5 : High measurement voltage range, 1X can measure 0 ~ 40 V, 10X can measure 0 ~ 400V , 100X can measure 0 ~ 4000V 6 : Up to 12 parameters measurement : VPP , VP , Vmax , Vmin , Vavg , Vrms , Frequent , Duty+ , Duty- , Time+ , Time- , Period 7 : Cursor measurement function, it is convenient to manually measure the period and frequency and voltage 8 : Complete triggering function (single, normal, automatic) 9 : At any time, the waveform display (pause function) is  freeze 10 : Equipped with high efficiency One-button AUTO 11 : One-button waveform storage and screenshot 12 : Built-in 1GB storage space, can store up to 1000 screenshots + 1000 sets of waveform data 13 : Powerful waveform picture manager supports thumbnail browsing, viewing, detailed viewing, page turning, deletion and waveform zooming in, zooming out, moving, etc. 14 : Equipped with a USB interface, which can be connected to a computer to share its screenshots with the computer, which is convenient for secondary analysis 15 : Lissajous figures graphic display function can be used to determine the amplitude, frequency, and phase contrast of two groups of signals 16 : FFT display function, can analyze the spectral characteristics of the signal 17 : Built in 6000mAh rechargeable lithium battery , Fully charged for 4 hours of continuous use at the highest screen brightness  18 : Memory compression technology, waveform refresh screen does not flicker 19 : Screen brightness adjustment 20 : Background grid brightness adjustment 21 : Ultra thin, easy to carry   Specifications:   1 : Analog band width: 100MHz * 2 2 : Number of channels : 2 channels 3 : Maximum real time sampling rate: 1GSa/s 4 : Vertical sensitivity: 50 mV/div ~ 500 V/div 5 : Horizontal time base range: 50S/div ~ 10nS/div 6 : Maximum test voltage: 40 V (1X probe), 400 V (10X probe) 7 : Storage depth: 240Kbit 8 : Input resistance: 1M 9 : ADC precision: 8bits 10 : Coupling mode: AC/DC 11 : Trigger mode: Single, Normal, Auto 12 : Trigger edge: Rising edge/Falling edge 13 : External trigger voltage 0 – 40 V 14 : Display: 7 inch - 800*480 15 : Operating: Capacitive touch screen + gesture 16 : Extension ports : USB picture export 17 : Power supply: 6000 mAh lithium battery 18 : Size: 184mm x 124mm x 50mm  19 : Total weight:650g   Package includes:   1 x ADS1013D oscilloscope host 2 x Matching 100MHz probe ( 1X and 10X ) 1 x 5V2A Charger ( Include USB data line ) 1 x User manual (English)   Details pictures:

Hantek DSO2C10 Digital Oscilloscope 2CH Digital Storage 1GS/s Sampling Rate 100MHz Bandwidth Dual Channel Economical Oscilloscope
Hantek DSO2C10 Digital Oscilloscope 2CH Digital Storag... $360.53

Features: 1), 2 channels, each channel has independent knob control; 2), Analog bandwidth 100MHZ 3) The highest sampling rate is 1 GSa/s; 4), The storage depth is 8Mpts; 5), The vertical range of 2mV/div ~ 10V/div; 6) Vertical resolution: 8bit; 7) Trigger: edge, pulse, video, slope, timeout, window, pattern, interval, runt, UART, LIN, CAN, SPI, IIC; 8) Bus decoding and protocol analysis: RS232/UART, I2C, SPI, CAN, LIN; 9), Can save settings, waveforms, reference waveforms, CSV, pictures and other data formats. 10), 3-digit digital voltmeter and 6-digit frequency meter functions; 11) Support 32 kinds of automatic measurement and statistics functions, real-time statistics of minimum, maximum, standard deviation and other statistical information; 12), Two groups of digital voltmeter functions; 13) Support threshold test to realize free measurement in the screen; 14), Rich SCPI remote control instructions; 15). Provide multiple types of peripheral interfaces: USB Host/Device. Product Model(NOTE:Click on the model to reach the purchase link of the corresponding model): Model           Channels Bandwidth Sampling Rate Storage Depth Signal Source (AWG) >>DSO2C10<< 2CH 100MHz 1GSa/S 8M / >>DSO2C15<< 2CH 150MHz 1GSa/S 8M / >>DSO2D10<< 2CH+1CH 100MHz 1GSa/S 8M 1CH >>DSO2D15<< 2CH+1CH 150MHz 1GSa/S 8M 1CH >>Please Click Here to Download the English User Manual<< >>Click to Download DSO2000 Software<< Specification: model DSO2D15 DSO2D10 DSO2C15 DSO2C10 bandwidth 150MHz 100MHz 150MHz 100MHz Number of oscilloscope channels 2CH 2CH 2CH 2CH Built-in signal source 1CH 1CH  -  - Oscilloscope index Sampling rate range 1GSa/s (single channel), 500MSa/s (dual channel) Collection method sampling Sample data Peak-to-peak Display high frequency and random glitches average value Average waveform, times: 4, 8, 16, 32, 64, 128 High precision Up to 12bit enter Input coupling DC, AC or ground (DC, AC, GND) input resistance 1MΩ±2% ‖20pF±3pF Probe attenuation coefficient setting 1X, 10X, 100X, 1000X Voltage level 300V CAT II Maximum input voltage 300VRMS (10X) Horizontal system Waveform interpolation (sin x)/x Maximum record length Maximum 8M per channel Maximum 4M for dual channels Horizontal scale range 2ns/div~100s/div 1, 2, 5 steps Time base mode YT, XY, Roll  Zero offset ±0.5 div×minimum time base gear Sampling rate and delay time accuracy ±50ppm Clock drift ≤±5 ppm/year Incremental time measurement accuracy Single, "sampled" mode (Full bandwidth) ±(1 sampling interval+100ppm×reading+0.6ns) >16 times above average ±(1 sampling interval+100ppm×reading+0.4ns) Sampling interval = second/div÷200 Vertical system model DSO2D15 DSO2D10 DSO2C15 DSO2C10 bandwidth 150MHz 100MHz 150MHz 100MHz Rise time at BNC (typical) 2.3ns 3.5ns 2.3ns 3.5ns Vertical resolution 8-bit resolution, simultaneous sampling for each channel Vertical sensitivity 2mV/div to 10V/div Offset range 2mV/div to 20mV/div, ±100mV; 50mV/div to 200mV/div, ±1V; 500mV / div to 2V / cell, ± 10V; 5V / div to 10V / division, ± 50V computation Add, subtract, multiply, divide, FFT FFT Window: Rectangular, Hanning, Hamming, Brackman, Bartlett, flat top window Bandwidth limit 20MHz Low frequency response (-3db) ≤10Hz at BNC Vertical gain accuracy In the "sample" or "average" acquisition mode, the accuracy of 10V/div to 10mV/div is ±3%; In "Sampling" or "Average" acquisition mode, the accuracy of 5mV/div to 2mV/div is ±4% DC offset accuracy ±0.1 div±2 mV±1% offset value Voltage measurement repeatability, average acquisition mode Under the same settings and environmental conditions, the voltage increment between any two sets of average values ​​of more than 16 waveforms: ±(3%×reading+0.05 division) Note: The bandwidth is reduced to 6MHz when using X1 probe Trigger system Trigger type Edge, pulse, video, slope, timeout, window, pattern, interval, runt, UART, LIN, CAN, SPI, IIC Trigger level range  ±5 divisions from the center of the screen Trigger mode Automatic, normal, single Level CH1~CH2 ±4 divisions from the center of the display EXT 0~3.3V Range of relief 8ns~10s Trigger level accuracy CH1~CH2 0.2 divisions × volts/div within ±4 divisions from the center display EXT ±(6%+40mV of setting value) Edge Trigger Slope Rising edge, falling edge, rising edge or falling edge Source CH1, CH2, EXT Pulse width trigger polarity Positive polarity, negative polarity Condition (When) <, >, !=, = Source CH1~CH2, Pulse width range 8ns ~ 10s Precision 8ns Video trigger Signal standard NTSC, PAL Source CH1~CH2 Synchronize Scan line, line number, odd field, even field, all field Slope trigger Slope Rise and fall Condition (When) <,>, !=, = Source CH1 ~ CH2 time limit 8ns ~ 10s Precision 8ns Timeout trigger Source CH1~CH2, polarity Positive polarity, negative polarity time limit 8ns ~ 10s Precision 8ns Window trigger Source CH1~CH2  Pattern trigger Pattern 0: low level; 1: high level; X: ignore; :rising; :falling; :rising or falling Level (source) CH1~CH2 Interval trigger Slope Rise and fall Condition (When) <,>, !=, = Source CH1~CH2, time limit 8ns ~ 10s Precision 8ns Runt trigger polarity Positive polarity, negative polarity Condition (When) <,>, !=, = Source CH1~CH2 time limit 8ns ~ 10s Precision 8ns UART trigger Condition (When) Start, stop, data, parity, receive error Source (RX/TX) CH1~CH2  Data Format Hex (hexadecimal) Data length 1 byte Data bit width 5 bit, 6 bit, 7 bit, 8 bit Parity check None, odd, even Idle level High, low Baud rate (optional) 110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s Baud rate (custom) 300bit/s~334000bit/s LIN trigger Condition (When) Interval field, sync field, ID field, sync error, identifier, ID and data Source CH1~CH2, Data Format Hex (hexadecimal) Baud rate (optional) 110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s Baud rate (custom) 300bit/s~334000bit/s CAN trigger Condition (When) Start bit, remote frame ID, data frame ID, frame ID, remote frame data, data frame data, error frame, all errors, response error, overload frame Source CH1~CH2 Data Format Hex (hexadecimal) Baud rate (optional) 10000, 20000, 33300, 500000, 62500, 83300, 100000, 125000, 250000, 500000, 800000, 1000000 Baud rate (custom) 5kbit/s~1Mbit/s   SPI trigger Source CH1~CH2, Data Format Hex (hexadecimal) Data bit width 4, 8, 16, 24, 32 IIC trigger Source (SDA/SCL) CH1~CH2, Data Format Hex (hexadecimal)          Data index 0~7 Timing (condition) Start bits, stop bits, no answer, address, data, reboot measuring cursor Voltage difference between cursors△V Time difference between cursors△T The reciprocal of △T, in Hertz (1/△T) Automatic measurement Frequency, period, average value, peak-to-peak value, root mean square, minimum value, maximum value, rise time, fall time, positive pulse width, negative pulse width, bottom value, top value, middle value, amplitude, overshoot , Preshoot, rising edge phase difference, falling edge phase difference, positive duty cycle, negative duty cycle, cycle average, cycle root mean square, falling edge overshoot, rising edge preshoot, BWIDTH, FRF, FFR, LRR , LRF, LFR, LFF DVM data source CH1, CH2 Measurement type DC effective value AC effective value Direct current frequency meter Hardware 6-digit frequency counter Signal source indicator Number of channels 1 channel Sampling Rate 200MSa/s Vertical resolution 12 bits  Highest frequency 25 MHz  Standard waveform Sine, square wave, pulse, triangle wave, sampling wave, exponential wave, noise Arbitrary waveform Arb1, Arb2, Arb3, Arb4 Sine Frequency Range 0.1Hz~25MHz Square wave/pulse Frequency Range 0.1Hz ~ 10MHz Triangle wave Frequency Range 0.1Hz~1MHz Sample wave Frequency Range 0.1Hz~1MHz Exponential wave Frequency Range 0.1Hz~5MHz noise   Arbitrary Wave 1 Frequency Range 0.1 Hz to 10 MHz  Arbitrary Wave 2 Frequency Range 0.1 Hz to 10 MHz  Arbitrary Wave 3 Frequency Range 0.1 Hz to 10 MHz  Arbitrary Wave 4 Frequency Range 0.1 Hz to 10 MHz  Wave length 8KSa frequency Precision 100 ppm (less than 10 kHz) 50 ppm (greater than 10 kHz) Resolution 0.1 Hz or 4 bits, whichever is greater Amplitude Output range 10mV~7Vp-p (high impedance) 5mV~3.5Vp-p(50Ω) DC offset range ±3.5 V, high resistance ±1.75 V, 50 Ω Resolution 100 μV or 3 bits, whichever is greater Precision 2% (1 kHz) Output impedance 50 Ω General technical specifications display Display type 7" TFT LCD display diagonally Display resolution 800 (horizontal) * 480 (vertical) pixels Display color 16 million colors (24 bit true color) Afterglow time Minimum value, 1 s, 5 s, 10 s, 30S, unlimited Display type Point, vector Display brightness Adjustable Grid type Optional Grid brightness Adjustable interface Standard interface USB Host, USB Device General technical specifications Probe compensator output Output voltage, typical About 2Vpp input ≥1MΩ load Frequency, typical 1kHz voltage 100-120VAC RMS (±10%), 45Hz to 440Hz, CATⅡ 120-240VAC RMS (±10%), 45Hz to 66Hz, CATⅡ Power consumption Less than 30W Fuse T, 3.15A, 250V, 5x20mm Operating temperature 0~50 °C (32~122 °F) storage temperature -40~+71 °C (-40~159.8 °F) humidity ≤+104℉(≤+40°C): ≤90% relative humidity 106℉~122℉ (+41°C ~50°C): ≤60% relative humidity Altitude When operating and not operating 3,000m (10,000 feet) Mechanical shock Random vibration 0.31g RMS from 50Hz to 500Hz , 10 minutes per axis When not operating 2.46g RMS from 5Hz to 500Hz , 10 minutes per axis During operation 50g, 11ms, half sine wave Mechanical part Oscilloscope size 318 x 140 x 150mm (length x width x height) weight 2900g   Package includes: 1 X Hantek DSO2C10 Digital Oscilloscope Details pictures: 

Hantek DSO4204B Digital Storage Oscilloscope 4 Channels 200MHz bandwidth 7inch DSO4204B 1GSa/s Record Length 64K
Hantek DSO4204B Digital Storage Oscilloscope 4 Channel... $734.10

Features: 4 Channels  oscilloscope+EXT+DVM+auto range function. 80-250MHz bandwidth,minimum range 500μV /div,1GS/s sample rate. Over 32 types of auto measurement function. Advanced digital trigger system, high trigger sensitivity.  Over 14 types of trigger function: edge, overtime, pulse, pattern, interval, etc. Integrated USB Host/Device, convenient to communicate with PC. Support U-stick storage/systerm update. Support a variety of SCPI remote control command. Support optional RS232 port, LAN port, HDMI port, touch screen, WIFI communication, SD card storage. Stable and reliable quality, sturdy and durable. Package included: DSO4204B Digital Storage Oscilloscope   Details pictures:

FY6900 Dual Channel DDS Function Arbitrary Waveform Signal Generator Pulse Signal Source Frequency Counter Fully Numerical Control 20MHZ/60MHZ
FY6900 Dual Channel DDS Function Arbitrary Waveform Si... from $144.70

Main Features:   ♦  Adopt the Direct Digital Synthesizer (DDS) technology and provide stable, precise, pure and low distortion signals.  ♦  2.4 inch TFT Color LCD with 320×240 resolution, displaying parameters and graphics of the two channels at the same time. ♦  The instrument uses 14-bit high-speed D/A converter chip (5Vpp output quantization error is less than 1mV), 250MSa/s sample rate, 14bits vertical resolution. ♦  Can output up to 97 groups of functions / arbitrary waveform, contains 33 groups of preset waveforms and 64 groups of user-defined waveforms. Preset waveforms: Sine, Square (Duty Cycle adjustable), Pulse (Pulse width and cycle time can be set accurately), Triangle/Ramp, CMOS(0~12V), Four channels TTL, Exponential Rise, Exponential Fall, Noise, ECG, DC etc. ♦  Enable to store 64 arbitrary waveform data files, each one of waveform storage depth 8192 points * 14bits; (The longer the waveform storage depth, the more detail the waveform is saved, and the signal details can be restored with high p'recision.) ♦ Various modulation types: AM, FM, PM, ASK, FSK and PSK modulations. ♦  Sweep Function: It can sweep 4 properties of signals including frequency, amplitude, offset and duty cycle; It has Linear and Logarithm two sweep types; 0.01S~999.99S sweep time; Up, Down and roundtrip sweep directions. ♦  VCO Function (Voltage Control Output): Can be achieved by an external input signal: voltage controlling frequency, voltage controlling amplitude, voltage controlling offset, voltage controlling duty cycle and PWM modulations. ♦  Burst Output Function: There has Manual Trigger, internal CH2 Trigger, and External Trigger for your options. It can output 1~1048575 pulse trains. ♦  100M Frequency meter function: It can measure frequency, period, pulse width and duty cycle. Max. frequency workable is 100MHz and Min. frequency workable is 0.01 Hz. ♦  Counter Function: It has 2 coupling measure modes including DC coupling and AC coupling. This design can solve inaccuracy problem of AC coupling. ♦  Standard dual full functional channels which are equivalent to two independent generators. ♦  Channel SYNC Function: Support waveform copy and state copy between channels. Support two or more signal generators connected to achieve multi-channel output, the maximum support 16-channel synchronous output, the phase between each channel can be adjusted. ♦  Precisely adjust the phases of the two channels, P'recision can be 0.01°. ♦ Min amplitude resolution can be up to 1 mV. Amplitude range is 0~24Vpp. ♦  Duty-cycle of each channel can be adjusted independently0.01%-99.99%, the adjusting resolution is 0.01%. ♦  -12V~+12V DC Offset function. Resolution 0.001V. ♦  Save function: It can save 20 sets user-set parameters and can be loaded at any time. ♦  Communicating function: All functions can be controlled by PC program and the communication protocol is open for secondary development. ♦  Output short-circuit protection: All channels can work more than 60 seconds when the load is short-circuited. ♦  Provide powerful waveform editing PC software. Users can download arbitrary waveform to this instrument after edit through PC program which is included in user CD. ♦  Adopt ABS plastic shell with table type design. Use 100-240V (AC) wide range voltage power supply.  ♦  Can choose our FYA2000S series or FPA1000 series power amplifier to output 20W~100W signal in DC-10MHz width without any distortion. FY6900 can output Function/Arbitrary Waveform including: >Sine >Square >Rectangle >Triangle/Ramp >Rise Sawtooth >Fall Sawtooth >Lorenz Pulse >Multitone >Noise >Electrocardiogram (ECG) >Trapezoidal Pulse >Sinc Pulse >Narrow Pulse >Gauss White Noise >Step Triangle >Positive Step >Inverse Step >Positive Exponent   >Inverse Exponent >Positive Falling Exponent >Inverse Falling Exponent >Positive Logarithm >Inverse Logarithm >Positive Falling Logarithm >Inverse Falling Logarithm >Linear FM >AM >FM >Positive Half Wave >Negative Half Wave >Positive Half Wave   Rectification >Negative Half Wave Rectification >User-defined waveform Technical Specification: Frequency Model FY6900-20M     FY6900-30M FY6900-50M FY6900-60M Sine 0~20MHz 0~30MHz 0~50MHz 0~60MHz Square 0~15MHz 0~25MHz 0~25MHz 0~25MHz Ramp, Triangle 0~10MHz 0~10MHz 0~10MHz 0~10MHz Pulse 0~10MHz 0~10MHz 0~10MHz 0~10MHz TTL/CMOS 0~10MHz 0~10MHz 0~10MHz 0~10MHz Arbitrary Waveform 0~10MHz 0~10MHz 0~10MHz 0~10MHz Min pulse width 20ns(All models of pulse wave min width can be 20ns) Min. Resolution on all frequency range 1μHz (Min. resolution can low to 1μHz on all frequency range to ensure adjusting accuracy under high frequency. For example, it can output 10.000000000001MHz signal). Accuracy ±20ppm Stability ±1ppm/ 3hours Waveform Characteristics Waveforms Sine, Square, Rectangle (Duty Cycle adjustable), Pulse (Pulse width and cycle time can be set accurately), Triangle/Ramp, Sawtooth Wave, CMOS, Four channels TTL, DC, Half wave, Full wave, Positive Step, Inverse Step, Positive Exponent, Inverse Exponent, Lorenz Pulse, Multitone, Noise, ECG, Trapezoidal Pulse, Sinc Pulse, Narrow Pulse, Gauss White Noise, AM, FM, and other 64 sets customer-defined waveform. Non-Volatile Storage Can store 64 user-defined arbitrary waveforms, (8K 14bits) * 64 Waveform Length 8192 points * 14bits Sampling Rate 250MSa/s Vertical Resolution 14 bits Sine Harmonic Suppression ≥50dBc(<1MHz); ≥45dBc(1MHz~20MHz); Total Harmonic Distortion <0.5% (20Hz~20kHz,0dBm) Rectangle Rise/Fall Time ≤7ns (VPP<5V) Overshoot ≤5% Duty Cycle 0.01%~99.99% (Resolution 0.01%) Sawtooth wave Linearity >99% (0.01Hz~10kHz) Output characteristics Amplitude(VPP) Frequency≤5MHz: 1mVpp~24Vpp; 5MHz 10MHz Frequency>20MHz: 1mVpp~5Vpp; Resolution 1mV Amplitude Stability ±0.5%/ 5 Hours Amplitude flatness ±2.5%(<10MHz);±5%(>10MHz); Waveform Output Impedance 50Ω±10%(Typical) Protection All channels can work more than 60 seconds when the load is short-circuited.  DC Offset Offset Range Frequency≤20MHz: ±12V;  Frequency>20MHz: ±2.5V; Offset Resolution 1mV Phase Feature   Phase range 0~359.99° Phase resolution 0.01° TTL Output   TTL Level Amplitude >3Vpp Fan-out >8 TTL LOAD Rise/Fall Time ≤10ns CMOS Output Low Electric Level <0.3V High Electric Level 1V~12V Rise/Fall Time ≤18ns External Measurement Function Frequency, Period, Positive/Negative Pulse Width, Duty Cycle Input Voltage Range 1Vpp~20Vpp Frequency Meter Resolution 0.01Hz (Gate Time = 100S) Range 0.01Hz~100MHz Sensitivity Gate Time 3 grades (1S, 10S, 100S) adjustable Counter Range 0-4294967295 Coupling DC, AC Working Mode Manual Period Measurement Range 5ns ~ 20s DC coupling measurement Pulse Width Measurement Range 0ns ~ 20s Resolution 5ns Duty Cycle Range (Display) 0% ~ 100% Sweep Carrier Waveform Sine, Square, Ramp, Arbitrary (except DC) Sweep Type Linear or Logarithm Sweep Direction Up, Down and roundtrip sweep directions; Sweep Objects Frequency, Amplitude, Offset, Duty Cycle Sweep Time 0.01S~999.99S/Step Setting range Starting position and Finishing position can be set arbitrarily. Sweep Range Decided by Parameters setting. VCO (Voltage Control Output) Modulation signal range to input 0~5V VCO signal frequency range 0-2000Hz VCO control object voltage controlling frequency (VCF), voltage controlling amplitude , voltage controlling offset, voltage controlling duty cycle. VCO special function Can Amplitude Modulate (AM) or Frequency Modulate (FM) by external analog signal. Modulation Modulation Type AM, FM, PM, ASK, FSK, PSK Carrier Waveform Sine, Square, Triangle, Ramp, Arbitrary waveform (Except DC) AM Source Internal (CH2) / External (VCO IN Port) Modulating Waveform Sine, Square, Triangle, Ramp, Arbitrary waveform Depth 0% to 120% Modulating Frequency Internal : 1μHz~1MHz;  External: 1μHz~2KHz; FM Source Internal (CH2) / External (VCO IN Port) Modulating Waveform Sine, Square, Triangle, Ramp, Arbitrary waveform Modulating Frequency Internal : 1μHz~1MHz;  External: 1μHz~2KHz; PM Source Internal (CH2) / External (VCO IN Port) Modulating Waveform Sine, Square, Triangle, Ramp, Arbitrary waveform Phase Deviation 0° to 360° Modulating Frequency Internal : 1μHz~1MHz;  External: 1μHz~2KHz; ASK Source Internal (CH2), External (ASK IN Port), Manual Modulating Waveform Square with 50% duty cycle. Key Frequency 1μHz~10MHz FSK Source Internal (CH2), External (FSK IN Port), Manual Modulating Waveform Square with 50% duty cycle. Key Frequency 1μHz~10MHz PSK Source Internal (CH2), External (PSK IN Port), Manual Modulating Waveform Square with 50% duty cycle. Key Frequency 1μHz~10MHz Burst Function Carrier Waveform Sine, Square, Ramp, Arbitrary (except DC) Burst Count 1~1048575 Trigger Source Manual, Internal, External (AC/DC) G'eneral Specifications Display Type 2.4 inch, TFT Color Display. Save & Load Amount 20 Position 01 to 20 (01 for start default value) Interface Type USB to Serial interface Protocol C'ommand line mode, providing communication protocols. Communicating Speed 9600bps (Industrial standard) Power Voltage Range AC100V~240V Technic SMD, LSI, Reliable and durable Buzzer Can be turned on/off by setting. Operation Buttons and knob continuously. Environment Temp.: 0~40℃, Humidity:<80% Size 200mm * 190mm * 90mm (L * W * H) Weight 850g Package Size 25cm * 21cm * 10cm (L * W * H) Package Weight 0.98kg(Main engine, accessories and packing materials) Note: FY6900 supports English & Chinese  menu switch. The defaul language is English.  >>Please Click Here to Download the English User Manual<< Package Includes: 1 x FY6900 DDS Signal Generator 1 x Power Cable 1 x USB Data Cable  2 x BNC-Clip Cables 1 x BNC-BNC Cable Details Pictures:

ET3240 Original 22000 counts Benchtop Digital Multimeter with Large Clear Screen High Precision Desktop Multimeter
ET3240 Original 22000 counts Benchtop Digital Multimet... $287.98

>> Software and manual download << ET3240 is a 4½ digits, 22000 counts, dual digital benchtop true-RMS multimeter.The STM32 chip and external double integral AD used by this benchtop multimeter providing accurate measurement and stable performance. 3.5 inch 320 * 480 high resolution TFT LCD screen makes a clear reading, rich display, and a good visual effects. The benchtop multimeter is powered by electricity and provide full-function, full-range overload protection. Fresh and simple design with excellent performance makes them an ideal choice for electricians, electronics enthusiasts, engineers and colleges and universities. Main features: 4½ digits, 22000 counts. Dual parameter display: display two parameters of the same input signal. Measurement rate: FAST (7 times / sec), MID (5 times / sec), SLOW (2 times / sec). Trigger mode: Automatic trigger, single trigger, external trigger(optional). Range switching mode: Auto / Manual. 12 basic measurement functions: AC and DC voltage, AC and DC current, two-wire / four-wire resistance, period / frequency, diode, on-off test, capacitance, duty cycle. DCV basic accuracy: 0.05%. Mathematical functions: MX+B/MAX/MIN/dB/dBm/Rel/Comp Hi/Comp Low/ Statistics. Additional functions: Data hold, data record, data readback. keys can be locked. Open calibration function. Square wave output.(Optional.) Provide system settings, can configure the language(Chinese / English), buzzer, screen brightness, interface display style. Temperature: Thermocouple: K/N/R/S/T/B/E/J/WRe325/WRe526; RTD: PT100 / PT50 / Cu100 / Cu50. Communication Interface: Standard: USB Device; Support SCPI protocol. Technical indicators: Mode ET3240 Display digits 22000(4½) Maximum measurement speed 7 times / sec Function DC voltage DC current AC voltage AC current Accuracy ±(0.05%+3) ±(0.35%+10) ±(0.8%+80) ±(0.8%+80) Range 10uV~1000V 10nA~10A 10uV~750V 10nA~10A Highest resolution 10uV 10nA 10uV 10nA   -- 40Hz~100kHz 40Hz~10kHz Function Resistance Capacitance Frequence Period Accuracy ±(0.1%+6) ±(3.5%+30) ±(0.2%+10) ±(0.2%+10) Range 10mΩ~200MΩ 1pF~10mF 1Hz~20MHz 50ns~500ms Highest resolution 10mΩ 1pF 0.001Hz 0.01ns Others Mathematical functions MX+B/MAX/MIN/dB/dBm/Rel/Comp Hi/Comp Low/Hold/Statistics Resistance measurement Support 2-wire, 4-wire in two ways. Continuity test When the resistance is less than 30 ohms, the buzzer sounds. Diode test Measurable range: 0 ~ 2V AC+DCmeasurement Support. Trigger mode Standard: automatic trigger, single trigger; Optional: external trigger. Duty cycle measurement 5.0% ~ 95.0%. (the error is within 10 words.) Square wave output Frequence: 1Hz ~ 100kHz, amplitude: 3V.(Optional.) Limit test Support. Calibration Support. Temperature Thermocouple: K/N/R/S/T/B/E/J/WRe325/WRe526; RTD: PT100/PT50/Cu100/ Cu50. Communication Interface Standard: USB Device; Additional functions Data hold, data record, data readback. General technical specifications:   Power supply voltage: 220V AC±10%, 110V AC ±10%, 45-65Hz. Working environment: 0~40℃, relative humidity < 80%. Storage environment: -10~50℃, relative humidity < 80%. Dsiplay: 3.5-inch, 320 * 480 resolution, 16 M colour TFT LCD. Dimensions: 265 mm * 105 mm * 305 mm.(width * height * depth). Weight: 2.3kg. Package includes: 1 X ET3240 Multimeter 1 X Table Pen 1 X Double-headed Three-core Power Cord 2 X Backup Power Fuse 1 X English User Manual 1 X EU Plug (We will send you a plug adapter according to your country.) Details pictures: 

Micsig STO1152C Digital Smart Oscilloscope 150MHz 2CH Handheld Oscilloscope Automotive Scopemeter Oscilloscope
Micsig STO1152C Digital Smart Oscilloscope 150MHz 2CH ... from $829.10

Features:   Bandwidth up to 150MHZ, 1 Gsa/s Sample Rate. Up to 28mpts Sample Memory Depth, 2 Channel  80, 000 Waveforms per Second 8 inch Full Capacitive Touch Display 256-level Intensity Grading and Color Temperature Display. High Quality Buttons and Knobs for Simple and Smart Operation 8GB Flash Memory with Unique File Management System for Easy Waveform Data Storage and Transfer Video Recording Function Ethernet and Wifi Network Access HDMI Port for External Display Remote Control using ios and Android APP   Specifications:   Brand: Micsig Size: 280*180*50MM Bandwidth:150MHZ Input channel:2 Sample rate:1G Sa/S Memory depth:28mpts Max capture rate:80,000wfm/s Bandwidth limitation:20MHZ, high pass, low pass Interface:WI-FI, LAN, HDMI, USB Host, USB Device, DC power, Trigger out Screen:8 inches TFT LCD, 800*600 pixels display resolution, 14"10 grids Battery(optional):Built-in lithium battery, working time is up to 5 hours continuously   Package included:   1 X STO1152C Smart oscilloscope 4 X Probes 1 X Power adaptor 1 X Power plug 5 X Color BNC cap   Notes:   1.Due to the difference between different monitors,the picture may not reflect the actual color of the item. We guarantee the style is the same as shown in the pictures. 2.Due to the manual measurement and different measurement methods, please allow 1-3cm deviation.Thanks!   Details pictures: 

DT71 Digital Mini Tweezers SMD Tester Portable LCR Meter Diode Resistor Capacitor Multimeter Frequency Signal Generator
DT71 Digital Mini Tweezers SMD Tester Portable LCR Met... $101.01

Features: DT71 Mini Digital Tweezers is a tool for multi-function measurements with full differential input measurement. DT71 has a unique trinary structure, which can be separated into the controller, testing arms, and tweezer tips, which are flexible to be replaced and combined. Innovative trinary structure: separated into the controller, testing arms, and tweezer tips, which are flexible to be replaced and combined. 360° rotatable controller with OLED screen, with good viewing angles. Smart gesture recognition with automatic identification of left/right-hand operation and adjusting the screen orientation accordingly. Hidden touch button on top of the controller, which makes it easy to operate with only a light touch. Test arms use magnetic elasticity to provide an easy clipping, ergonomic, and long-lasting structure. Built-in dual lithium batteries in test arms, balancing both arms and providing a longer standby time. Several kinds of gold-plated interchangeable tweezer tips, enabling higher measurement accuracy in various usages. Automatically identify SMDs including resistor, capacitor, inductor, and diode, showing both main and secondary parameters. A built-in signal generator can output a variety of waveform signals. Specification: Product Specifications Operation time 10 hrs (in continuous operation)     Charging time 2 hrs Display 96*16 OLED Size Controller 47mm Test Arms 106mm Weight 22g     Operation Hidden touch button     Measurement  Specifications   Range Resolution Accuracy Resistance 0.1Ω~1KΩ 0.1Ω 0.5%+2 1KΩ~2000KΩ 1KΩ 0.5%+2 Capacitance 0.1pF~1000pF 0.1pF 2%+3 0.001uF~400uF 0.001uF 2%+3 Inductance 1uH~1000uH 1uH 5%+3 1mH~50mH 1mH 5%+3 Voltage 1mV~100mV 1mV 2%+5 0.1V~40V 0.1V 1%+3 Frequency 10Hz~1KHz 10Hz 0.1%+3 1KHz~20000KHz 1KHz 0.1%+3 Diode silicon diodes, Schottky diodes, LEDs (+0.1~3V) 0.1V 1% Max input voltage -5V~+50V Source Impedance 1MΩ Functions Automatic Identification Yes Designated measurements Yes Continuity and Diode testing Yes Signal generator SINE Support: 10KHz, 5KHz, 2KHz, 1Khz, 500Hz, 200Hz   NOISE Support: 100KHz   USER Support: 10KHz, 5KHz, 2KHz, 1Khz, 500Hz, 200Hz   PULSE Support: 100KHz, 0KHz, 20Khz, 10KHz, 5KHz, 2KHz, 1Khz, 500Hz, 200Hz Package includes: 1 x DT71 Controller  1 x Test Arms  2 x Tweezer Tips 1 x Data Cable 1 x Carrying Case 1 x User Manual >>Please Click Here to Download the English User Manual<< Details pictures: 

DANIU™ LCR-TC1  1.8inch Colorful Display Multifunctional TFT Backlight Transistor Tester for Diode Triode Capacitor Resistor Transistor LCR ESR NPN PNP MOSFET
DANIU™ LCR-TC1 1.8inch Colorful Display Multifunction... $36.90

Please click here to download the English manual Description:   1.8inch Colorful Display Multi-functional TFT Backlight Transistor Tester for Diode Triode Capacitor Resistor Transistor LCR ESR NPN PNP MOSFET  Features:   It can be widely used to detect NPN and PNP transistor, capacitor, resistor, diode, triode, N-channel and P-channel MOSFET, IGBT, JFET, triac and battery etc.  It can also be used to detect  infrared wave forms.  It also can detect zener diode and has the function of self-calibration. After detection, align the infrared remote control with the "IR" light, then press the button in the remote control, if the detector successfully decode it, it will display the data code and infrared wave form. One button operation, automatically detect and shutdown, and you can press the multi-functional button to close the detector too. Put the pins of component in corresponding area, then dial the little handle and the detector will test it automatically, finally the results will display on the back light TFT screen clearly. Not like the usual black and white display, this detector will show results in color.   Specifications:   Display: 1.8 inch TFT Screen Diode Range: < 4.5V Zener Diode:Transistor Detect Area: 0.01-4.5V   Zener Diode Detect Area: 0.01-30V Triac Range: IGT < 6mA Capacitance: 25pF-100mF Resistor: 0.01-50MΩ Inductance: 0.01mH-20H Battery: 0.1-4.5V Power Mode: Rechargeable Lithium Battery ( INCLUDED) Item Size: 8.8 x 8 x 2.8cm / 3.47 x 3.15 x 1.10in                Item Weight: 111.5g / 3.94oz Package Size: 14.5 x 12 x 2.7cm / 5.71 x 4.73 x 1.06in Package Weight: 114g / 4.02oz   Packing included:   1 x Multi-functional TFT Transistor tester 1 x Electronic component set(Send Randomly) 3 x Test hooks >Click to veiw more info in FRENCH.pdf<  Details pictures:       , , , , , , , , ,

Hantek Digital LCR Meter Portable Handeld Inductance Capacitance Resistance Measurement Tester Tools
Hantek Digital LCR Meter Portable Handeld Inductance C... from $205.71

 Note:  the model marked on product name has been changed since 2020/08/28   old   →   new TO11 = 1832CTO22 = 1833C Features: 2.8 inch TFT LCD,Switch between Chinese and English HD display,dual display of measurement data,the result is clear Support data re cord analysis Support PC upper computer,easy to control and measure remotely Test lead:3 end/5 end switch Measuring speed:high speed/intermediate speed/low speed switch Range:support manual/auto switch and easy to do quick measurement LCR adopted rechargeable design,Large capacity lithium battery,super standby Double shock protection sleeve,allround protection,shakeproof,fallarrest,protect the machine from damage,longer use time, more comfortable measurement Bracket design,easy to put and measure   Specification:   Package included: 1 x Hantek LCR Meter Kit   Please click here to download the English manual Please click here to download the Firmware Please click here to download the Software Details pictures:

ET45 Series LRC Benchtop Digital Bridge Desktop LCR  LCR Tester LCR Meter Capacitance Resistance Impedance Inductance Measure
ET45 Series LRC Benchtop Digital Bridge Desktop LCR L... from $526.18

Descriptions: ET45 series desktop bridge incorporates 3.5-inch TFT display, user-friendly interface, and a variety of measurement parameters into one body. It is convenient for users to carry out remote control with USB and RS232 and also perform the sorting of components using handle. In function, it can not only adjust the output frequency and test level, but also record the value of components in the process of measurement. In the performance parameters, its basic accuracy reaches 0.2%. Features: ● Measurement frequency up to 100kHz ● Test level 100 ~ 2000mV ●Support the measurement of DC resistance and electrolytic capacitor ●Internal bias voltage output (1mV-1500mV) ●Automatic identification of component measurement ●3.5-inch TFT display, 5 and a half bits display ●USB, RS232 communication interface,Handle sorting ● Data recording function (maximum and minimum values, average value) ● Support SCPI communication protocol ● Provide system settings, which can configure language, buzzer, screen brightness, etc according to the needs of users. ● Basic accuracy 0.2% ● Manual and automatic range ● Be equipped with open circuit and short circuit correction ● Comparator has sorting and alarm function ● Provide a variety of test ports >>ET44 ET45 LCR bridge SCPI protocol Specifications: ●Power supply voltage: 220VAC ± 10%, or 110VAC ± 10%, 45-65Hz ●Working environment: 0 ~ 40 ℃, relative humidity <80%. ●Storage environment: -10 ~ 50 ℃, relative humidity <80%. ●Dimensions: 265mm * 105mm * 305mm (width * height* depth). ●Mass: 2.3kg. ●Power consumption: <10W >>Please Click Here to Download the English User Manual<< Package Includes: 1 x  ET45 Series LCR Tester 1 x Set of Accessories 1 x EU Plug Note: We will send you a plug adapter according to your country. Detail Pictures:  

ET44 Series Desktop Digital LCR Meter Capacitance Resistance Impedance Inductance Measure LCR Bridge LCR Meter
ET44 Series Desktop Digital LCR Meter Capacitance Resi... from $367.98

Descriptions:   ET44 series desktop bridge incorporates 3.5-inch TFT display, user-friendly interface, and a variety of measurement parameters into one body. It is convenient for users to carry out remote control with USB and RS232 and also perform the sorting of components using handle. In function, it can not only adjust the output frequency and test level, but also record the value of components in the process of measurement. In the performance parameters, its basic accuracy reaches 0.2%. Features: ● Measurement frequency up to 100kHz ● Test level 100 ~ 2000mV ●Support the measurement of DC resistance and electrolytic capacitor ●Internal bias voltage output (1mV-1500mV) ●Automatic identification of component measurement ●3.5-inch TFT display, 5 and a half bits display ●USB, RS232 communication interface, Handle sorting ● Data recording function (maximum and minimum values, average value) ● Support SCPI communication protocol ● Provide system settings, which can configure language, buzzer, screen brightness, etc according to the needs of users. ● Basic accuracy 0.2% ● Manual and automatic range ● Be equipped with open circuit and short circuit correction ● Comparator has sorting and alarm function ● Provide a variety of test ports Specifications: Model ET4401 ET4402 ET4410 Digits Main parameter: 5 digits; secondary parameter: 5 digits Measurement Parameter Main parameter: L/C/R/Z; secondary parameter: X/D/Q/θ/ESR Measurement Range(L)  0.01μH - 9999H Measurement Range(C) 0.01pF - 99999μF Measurement Range(R) 0.0001Ω - 99.99MΩ Basic Accuracy 0.2% Test Frequency (Hz) 100~10kHz  10 point 100~20kHz  12point 100~100kHz  20 point Measurement Display Speed 2 times/second (slow), 4 times/second (medium speed), 8 times/sec (fast) Internal Bias 0-1500mV adjustable, 1mV stepping Test Level 100mV, 300mV, 600mV, 1000mV, 1500mV, 2000mV Correction Function Open circuit correction, short circuit correction Screening function The screening limit can be set from -50% to + 50% with fixed points of 1%, 5%, 10% and 20% Selection of comparator Five gear sorting, third gear qualified, one gear failed, one ancillary gear Communication Interface Standard configuration: USB, RS232 (or 485), Handle interface; Optional: GPIB, USB Host Others Support DCR, electrolytic capacitor measurement mode, adjustable backlight brightness,  optional in English and Chinese ●Power supply voltage: 220V AC ± 10%, or 110V AC ± 10%, 45-65Hz ●Working environment: 0 ~ 40 ℃, relative humidity <80%. ●Storage environment: -10 ~ 50 ℃, relative humidity <80%. ●Dimensions: 265mm * 105mm * 305mm (width * height* depth). ●Mass: 2.3kg. ●Power consumption: <10W >>Please Click Here to Download the English User Manual<< Package Includes: 1 x ET4401 LCR Tester 1 x Set of accessories Detail Pictures:  

FNIRSI-1C15 Professional Digital Oscilloscope 500MS/s Sampling Rate 110MHz Analog Bandwidth Support Waveform Storage
FNIRSI-1C15 Professional Digital Oscilloscope 500MS/s ... $122.34

Description: FNIRSI-1C15 is a fully functional, practical and cost-effective handheld oscilloscope newly launched by FNIRSI. The real-time sampling rate is 500M, and the analog bandwidth is 110MHz. In addition to all the functions of a conventional handheld oscilloscope, we also added a one-key quick auto function on this basis, so you can easily grasp the waveform like a desktop computer. We have added 1k Hz self-test square wave for FNIRSI-1C15, and the storage depth has been upgraded to 12kpts. With reference to the waveform, you can pause at any time to save the previous frame waveform to the screen, and you can compare it with the currently refreshed waveform. Afterglow and scroll modes make it easier to detect and record waveforms. Built-in 3000mAH rechargeable battery, it can work continuously for more than 10 hours after fully charged. The body is equipped with a high-quality silicone sleeve, which is non-slip and anti-drop. The joystick replaces the original arrow keys, making the operation simpler and more effective. Product parameters: Model : FNIRSI-1C15Number of channels : 1Screen size : 2.4 inches  Screen Resolution : 320*240  Analog bandwidth : 110M  Sampling Rate : 500M  1k Hz self-checking square wave:Stand by  Rise Time : <3ns  Storage depth : 12 Kpts  Time base range : 5ns-10s  Vertical sensitivity : 20mv/div-100v/div  Trigger mode : Auto/Normal  Trigger type : Rising/Falling  Display mode : YT/scroll  Afterglow time : None/1s/∞  Charging method : 5V/800mA  Voltage measurement range : ± 40v (x1 file);± 400v (x10 file)  Channel coupling : AC-DC  One-button automatic : Stand by  Waveform measurement : 14 types  Measurement accuracy : ±2%  Reference waveform : Stand by  Waveform save : Stand by  Frequency accuracy : ±0.01% Package includes: 1 x Digital oscilloscope  1 x Alligator clip probe 1 x Data cable  1 x Charger Details pictures: 

Hantek DSO2C15 150MHz 1GSa/s Sampling Rate Dual-Channel Digital Storage Oscilloscope Digital Oscilloscope
Hantek DSO2C15 150MHz 1GSa/s Sampling Rate Dual-Channe... $433.42

Note: The model is of DSO2C15 . Feature: 1) 2 channels, both are respectively controlled by independent knobes; 2) 150MHZ analog channel bandwidth; 3) 1 GSa/s real-time sample rate; 4) 8M memory depth; 5) Vertical range 2mV/div ~ 10V/div; 6) Vertical resolution : 8bit; 7) Trigger: Edge, Pulse width, Video, Slope, Overtime, Window, Pattern, Interval, Delay, UART, LIN, CAN, SPI, IIC; 8) CAN decode and protocol analysis: RS232/UART、I2C、SPI、CAN、LIN 9) Can save as multiple data formats, such as setting, waveform, referance waveform, CSV, picture; 10) 5 bits digital voltage meter and 6 bits hardware frequency indicator function; 11) 32 kinds of auto measurements with statistics, real-time statistics of maxmum, minimum, standrad deviation and etc.; 12) 2 sets of digital voltmeter; 13) Support threshold testing, free measurements within the screen; 14) Abundant SCPI remote command control; 15) Many external interface: USB Host/Device. Product Model(NOTE:Click on the model to reach the purchase link of the corresponding model): Model           Channels Bandwidth Sampling Rate Storage Depth Signal Source (AWG) >>DSO2C10<< 2CH 100MHz 1GSa/S 8M / >>DSO2C15<< 2CH 150MHz 1GSa/S 8M / >>DSO2D10<< 2CH+1CH 100MHz 1GSa/S 8M 1CH >>DSO2D15<< 2CH+1CH 150MHz 1GSa/S 8M 1CH >>Please Click Here to Download the English User Manual<< >>Click to Download DSO2000 Software<< Specifications: Model: DSO2C15 Channel: 2 CH Bandwidth: 150MHz Sample rate: 1GSa/S Memory depth: 8M AFG: Without Parameters   Model DSO2D15 DSO2D10 DSO2C15 DSO2C10 Bandwidth 150MHz 100MHz 150MHz 100MHz Oscilloscope channels 2CH 2CH 2CH 2CH Waveform generator 1CH 1CH  -  - Oscilloscope Sample rate 1GSa/s (single channel) 500MSa/s (two channels) Acquisition Sampling Sample data Peak-to-peak value Display high frequency and random burr Average Average waveform, times:  4, 8, 16, 32, 64, 128 High resolution Up to 12bit Input Input coupling DC, AC, GND Input impedance 1MΩ±2% ‖20pF±3pF Probe attenuation  factor 1X, 10X, 100X, 1000X Voltage classes 300V CAT II Maximum input voltage 300VRMS (10X) Horizontal Waveform interpolation (sin x)/x Maximum record length Single channel maximum 8M Two channels maximum 4M Horizontal scale range 2ns/div~100s/div  1, 2, 5 step by step Time base mode Y-T, X-Y, Roll  Zero offset ±0.5 div×minimum time base gear Sample Rate and Delay Time Accuracy ±25ppm Clock drifting ≤±5 ppm/year Increment Time Measurement Accuracy single, ''acquisition'' mode (Full Bandwidth) ±(1 sample interval+100ppm×reading+0.6ns) >16 times averages ±(1 sample interval+100ppm×reading+0.4ns) Sample interval=sec/div÷200 Sample Rate and Delay Time Accuracy ±50ppm(at any interval greater than 1ms) Vertical Model DSO2D15 DSO2D10 DSO2C15 DSO2C10 Bandwidth 150MHz 100MHz 150MHz 100MHz Rising time in BNC position (typical) 2.3ns 3.5ns 2.3ns 3.5ns Vertical resolution 8 bits resolution, each channel samples simultaneously Vertical sensitivity 2mV/div to 10V/div Offset range 2mV/div to 20mV/div, ±100mV; 50mV/div to 200mV/div, ±1V; 500mV/div to 2V/div, ±10V; 5V/div to 10V/div, ±50V Mathematical operation +, -, ×, ÷, FFT FFT Window: Rectangular, Hanning, Hamming, Brackman, Bartlett, flat top window Bandwidth Limit 20MHz Bass response(-3db) In BNC position ≤ 10Hz Vertical gain accuracy In ''normal''  or ''average'' acquisition mode, the accuracy of 10V/div to 10mV/div is ±3%; In ''normal'' or ''average'' acquisition mode, the accuracy of 5mV/div to 2mV/div is ±4% DC offset accuracy ±0.1 div±2 mV±1% offset value Voltage measurement repeatability, average acquisition mode Under the same setting and environment, ≥16 waveforms are sampled, △V of any two averages: ±(3%×value+ 0.05 div) Note: Bandwidth reduced to 6MHz when using a 1X probe Trigger Trigger type Edge, Pulse width, Video, Slope, Overtime, Window, Pattern, Interval, Delay, UART, LIN, CAN, SPI, IIC Trigger level range  ±5 divisions from the center of the screen Trigger mode Auto, general, single Level CH1~CH2 ±4 divisions from the center of the screen EXT 0~3.3V Holdoff range 8ns~10s Trigger level accuracy CH1~CH2 0.2 div×volts/div within ±4 divisions from the center of the screen EXT ±(Set value× 6%+40mV) Edge trigger Slope Rising edge, falling edge, rising or falling edge Signal source CH1, CH2, EXT Pulse width trigger Polarity Positive polarity, negative polarity Condition(When) <, >, !=, = Signal source CH1~CH2, Pulse width range 8ns ~ 10s Accuracy 8ns Video trigger Signal standard NTSC, PAL Signal source CH1~CH2 Synchronization Scanning line, line number, odd field, even field, all field Slope trigger Slope rise, fall Condition(When) <, >, !=,  = Signal source CH1 ~ CH2 Time range 8ns ~ 10s Accuracy 8ns Overtime trigger Signal source CH1~CH2, Polarity Positive polarity, negative polarity Time range 8ns ~ 10s Accuracy 8ns Window trigger Signal source CH1~CH2  Pattern trigger Pattern 0: low level; 1: high level; X: ignore Level(signal source) CH1~CH2 Interval trigger Slope rise, fall Condition(When) <, >,  !=,  = Signal source CH1~CH2 Time range 8ns ~ 10s Accuracy 8ns Delay trigger Polarity Positive polarity, negative polarity Condition(When) <, >, !=, = Signal source CH1~CH2 Time range 8ns ~ 10s Accuracy 8ns UART trigger Condition(When) start, stop, data, odd-even check, reception error Signal source(RX/TX) CH1~CH2  Data format Hex (hexadecimal) Data length 1 byte Data bit width 5 bit, 6 bit, 7 bit, 8 bit Odd-even check none, odd, even Free level high, low Baud rate (optional) 110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s Baud rate(user-defined) 300bit/s~334000bit/s LIN trigger Condition(When) Interval field, synchronization field, ID field, synchronization error, identifier, ID and data Signal source CH1~CH2 Data format Hex (hexadecimal) Baud rate (optional) 110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s Baud rate(user-defined) 300bit/s~334000bit/s CAN trigger Condition(When) Start bit, remote frame ID, data frame ID, frame ID, remote frame data, data frame data, wrong frame, all errors, answer error, overload frame Signal source CH1~CH2 Data format Hex (hexadecimal) Baud rate (optional) 10000, 20000, 33300, 500000, 62500, 83300, 100000, 125000, 250000, 500000, 800000, 1000000 Baud rate(user-defined) 5kbit/s~1Mbit/s   SPI trigger Signal source CH1~CH2 Data format Hex (hexadecimal) Data bit width 4, 8, 16, 24, 32 IIC trigger Signal source (SDA/SCL) CH1~CH2 Data format Hex (hexadecimal)         Data index 0~7 Opportunity(condition) Start bit, stop bit, no response, address, data, restart Measurement Cursor Voltage difference between cursors △V Time difference between cursors △T Reciprocal of △T, in Hertz (1/△T) Auto measurement frequency, period, mean, peak-to-peak, RMS, minimum, mixmum, rising time, falling time, + width, - width, base, top, middle, amplitude, overshoot, preshoot, rising edge phase difference, falling edge phase difference, + duty, - duty, period mean, PRMS, FOVshoot, ROVshoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF DVM Data source CH1, CH2 Measurement type DC effective value AC effective value DC Frequency meter hardware 6 bits frequency meter Arbitrary waveform generator Channel 1 Sample rate 200MSa/s Vertical resolution 12 bits  Maximum frequency 25 MHz  Standard waveforms sin、square, pulse, triangular, sampling wave, index, noise Arbitrary waveform Arb1, Arb2, Arb3, Arb4 Sin Frequency range 0.1Hz~25MHz Square/pulse Frequency range 0.1Hz~10MHz Triangular wave Frequency range 0.1Hz~1MHz Sampling wave Frequency range 0.1Hz~1MHz Index Frequency range 0.1Hz~5MHz Noise    Arb1 Frequency range 0.1 Hz to 10 MHz  Arb2 Frequency range 0.1 Hz to 10 MHz  Arb3 Frequency range 0.1 Hz to 10 MHz  Arb4 Frequency range 0.1 Hz to 10 MHz  Waveform length 8KSa Frequency Accuracy 100 ppm (<10 kHz) 50 ppm (>10 kHz) Resolution 0.1 Hz or 4 bits,take the greater one Amplitude Output range 10mV~7Vp-p (high impedance) 5mV~3.5Vp-p (50Ω) DC offset Range ±3.5 V, high impedance ±1.75 V, 50 Ω Resolution 100 μV or 3 bits, take the greater one Accuracy 2% (1 kHz) Output impedance 50 Ω General specifications Display Display type 7'' diagonal TFT liquid crystal Display resolution 800 (horizontal)*480 (vertical) pixels Display colour 16 million colours (24 bits true colour) Persistence time minimum, 1 s, 5 s, 10 s, 30S, infinite Display type dot, vector Display brightness adjustable Grid type adjustable Grid brightness adjustable Interface Standard interface USB Host,USB Device General specifications Probe compensator output Output voltage, typical about 2Vpp input ≥1MΩ load Frequency, typical 1kHz Power supply 100-120VACRMS(±10%), 45Hzto 440Hz, CATⅡ 120-240VACRMS(±10%), 45Hz to 66Hz, CATⅡ Power consumption <30W Fuse T, 3.15A, 250V, 5x20mm Operating temperature 0~50 °C (32~122 °F) Storage temperature -40~+71 °C (-40~159.8 °F) Humidity ≤+104℉(≤+40°C): ≤90% relative humidity 106℉~122℉ (+41°C ~50°C): ≤60% relative humidity Altitude Operating and nonoperating 3, 000m (10, 000 feet) Mechanical shock Random vibration 0.31 g RMS from 50Hz to 500Hz, 10 minutes on each axis Nonoperating 2.46g RMS from 5Hz to 500Hz, 10 minutes on each axis Operating 50g, 11ms, half-sine wave Mechanical Size 318 x 140 x 150mm (length x width x height) Weight 2900g Package Includes: Details pictures: 

DANIU ADS5012H Digital 2.4-inch TFT Screen Anti-burn Oscilloscope 500MS/s Sampling Rate 100MHz Analog Bandwidth Support Waveform Storage and Built-in Large 3000mah Capacity Lithium Battery
DANIU ADS5012H Digital 2.4-inch TFT Screen Anti-burn O... $138.54

In order to save costs, the material of screen has changed to TFT from IPS. And the battery capacity has also reduced to 3000mAh. So.....Just made A few minor changes, the price has gone down a lot!!! -2019.6.24 DANIU Team Description:   The ADS5012H is a versatile, highly practical, cost-effective handheld oscilloscope for the maintenance industry and the R&D industry with DANIU's real-time sampling rate of up to 500MS/s and 100MHz analog bandwidth.With full trigger function (single, normal, automatic), it can be used freely for both periodic analog signals and non-periodic digital signals. The built-in high voltage protection module can  withstand  up to 400V continuous voltage and 600V peak voltage. There is no need to worry about the oscilloscope burnout caused by the high voltage not being probed to the 10X position.Large time base scan mode that monitors slow level changes. Equipped with high-efficiency one-button AUTO, the measured waveform can be displayed without complicated adjustment. Display high-definition LCD screen with 2.4-inch 320*240 resolution TFT full-vision technology, the visual effect is very good. Extremely convenient and fast waveform storage function, built-in 64M storage space, can store up to 2000 waveform pictures, the storage process is simple and fast, save the current waveform anytime and anywhere, just one touch, no cumbersome tips and choices. Powerful waveform file manager, support for thumbnail browsing, viewing, detail viewing, page turning, deletion and more. Built-in 3000mah high-quality lithium battery, can be used continuously for 8 hours when fully charged.The body is equipped with high-quality silicone protective cover, non-toxic and lead-free environmental protection, anti-skid, anti-shock and shockproof, comprehensive protection of the fuselage, soft texture, feel very comfortable. Key Features:   1 : Intelligent anti-burn , 1X Can withstand up to 600V withstand voltage 2 : Afterglow display technology 3 : 2.4 inch TFT color display screen 4 : 100MHz analog bandwidth @ 500MS/s sampling rate ( 1X = 5MHz , 10X = 100MHz ) 5 : One-button waveform storage 6 : Built-in 64M storage space, the maximum storage of 2000 waveform pictures 7 : Powerful waveform file manager, support thumbnail browsing, viewing, details view, flip, delete and other functions 8 : High measurement voltage range, 1X can measure 0 ~ 80 V, 10X can measure 0 ~ 800V 9 : Up to 12 parameters measurement : VPP , VP , Vmax , Vmin , Vavg , Vrms , Frequent , Duty+ , Duty- , Time+ , Time- , Time 10 : At any time, the waveform display (pause function) is frozein 11 : Equipped with high efficiency One-button AUTO 12 : Complete triggering function (single, normal, automatic) 13 : Built in 3000mAh rechargeable lithium battery , Fully charged for 8 hours of continuous use 14 : Screen brightness adjustment 15 : Memory compression technology, waveform refresh screen does not flicker 16 : Anti-slip anti-drop silicone sleeve 17 : Ultra small volume, easy to carry   Specifications:   1 : Analog band width: 100MHz 2 : Maximum real time sampling rate: 500MS/s 3 : Vertical sensitivity: 50 mV/div ~ 100 V/div 4 : Horizontal time base range: 50S/div ~ 6nS/div 5 : Maximum test voltage: 80 V (1X probe), 800 V (10X probe) 6 : Storage depth: 128KB 7 : Input resistance: 1M 8 : ADC precision: 8bits 9 : Coupling mode: AC/DC 10 : Trigger mode: Single, Normal, Auto 11 : Trigger edge: Ascending/descending edge 12 : External trigger voltage 0 – 80 V 13 : Display: 2.4 inch - 320*240 - TFT process 14 : Power supply: 3000 mAh lithium battery 15 : Size: 114mm x 74mm x 33mm  16 : Weight: 300g Package Includes:   1 x ADS5012H Oscilloscope Host 1 x Matching 100MHz Probe ( 1X and 10X ) 1 x Micro USB Data Line 1 x User Manual (English) 1 x High Quality Package Detail Pictures:

ANENG AN9002 Digital bluetooth True RMS Multimeter 6000 Counts Professional Auto Multimetro AC/DC Current Voltage Tester
ANENG AN9002 Digital bluetooth True RMS Multimeter 600... $48.10

Description: ANENG AN9002 is a newly upgraded professional multimeter, which can realize remote operation and measurement through Bluetooth technology. The measurement data of it is visualized and recordable through the Bluetooth of the mobile phone, It help us make the measurement more convenient and more accurate. Features: This products is a battery-powered ,ture-rms ,auto-ranging digital multimeter with a 6000 counts LCD display and a backlight. Measure AC/DC Voltage Measure AC/DC Current Test Continuity/Diodes/Resistance Measure Capacitance/Frequency Measure Duty Cycle/Temperature Specification: Brand ANENG Model AN9002 Display(LCD) 6000 counts Ranging Auto/Manual Material ABS Update Rate 3 times/second True RMS yes Data Hold yes Backlight yes Low Battery Indication yes Auto Power Off yes Battery Type 2 * 1.5V AA Battery (Without) Function Range Accuracy DC Voltage 60mV/600mV/6V/60V/600V/1000V ±(0.5%+3) AC Voltage 60mV/600mV/6V/60V/600V/750V ±(1%+3) DC Current 600uA/6000uA/60mA/600mA/6A/10A ±(1.2%+3) AC Current 600uA/6000uA/60mA/600mA/6A/10A ±(1.5%+3) Resistance 600Ω/6kΩ/60kΩ/600kΩ/6MΩ ±(0.5%+3)   60MΩ ±(1.5%+3) Capacitance 9.999nF ±(5.0%+20)   99.99nF/999.9nF/9.999uF/99.99uF/999.9uF ±(2.0%+5)   9.999mF ±(5.0%+5) Frequency 99.99Hz/999.9Hz/9.999kHz/99.99kHz/999.9kHz/9.999MHz ±(0.1%+2) Duty Cycle 1%~99% ±(0.1%+2) Temperature (-20~1000)℃/(-4~1832)℉ ±(2.5%+5) Diode : yes Continuity : yes Bluetooth : yes Package includes: 1 * ANENG AN9002 digital multimeter (not including battery) 2 * Pair of electron probes 1 * Temperature measurement line 1 * User Manual Details picture:

FUYI FY219 Double Display AC/DC True RMS Digital Clamp Meter Portable Multimeter Voltage Current Meter Inrush Current V.F.C  Frequency Conversion Low Impedance Voltage Measurement
FUYI FY219 Double Display AC/DC True RMS Digital Clamp... $65.42

Feature:   1. This portable LCD clamp meter features with high reliability, high safety and easy operation. 2. Support for measurement of AC DC voltage, AC DC current, resistance, capacitance, and more. 3. Support for full range overload protection, a perfect electrical measurement instrument. 4. Support for V.F.C frequency conversion measurement and support for NCV strong electric induction. 5. Widely used in the detection, maintenance and repair of power equipment such as electric power and circuits. 6. True RMS clamp meter and support for measurement inrush current(can measure the instant start current),low impedance voltage. Specification: Condition: 100% Brand New Item Type: Clamp Meter Material: ABS Model Range Resolution Accuracy DC Voltage 600mV/6V/60V 0.1mV/0.001V/0.01V ± (0.8% Reading + 3 Digits) 600V 0.1V ± (1.0% Reading + 3 Digits) AC Voltage 6V/60V/600V 0.001V/0.01V/0.1 ± (1.2% Reading + 5 Digits) 200-600V (V.F.C) 1V ± (1.5% Reading + 10 Digits) AC Current 60A 10mA ± (3.0% Reading + 10 Digits) V.F.C Mode ± (4.0% Reading + 10 Digits) 600A 100mA DC Current 60A 10mA ± (3.0% Reading + 10 Digits) 600A 100mA Resistance 600Ω/6KΩ/60KΩ/600KΩ/6MΩ 0.1Ω/0.001KΩ/0.01KΩ/0.1KΩ/0.001MΩ ± (0.8% Reading + 3 Digits) 60MΩ 0.1MΩ ± (2.0% Reading + 5 Digits) Capacitance 60nF/600nF/6μF/60μF/600μF/6mF/60mF 0.01nF/0.1nF/0.001μF/0.01μF/0.1μF/0.001mF/0.01mF ± (4% Reading + 3 Digits) Frequency (Clamp Frequency Measurement, A File) 600Hz 0.1Hz ± (1.5% Reading + 5 Digits) 1KHz 0.001KHz Frequency (Clamp Frequency Measurement, V File) 600Hz 0.1Hz ± (1.5% Reading + 5 Digits) 6KHz 0.001KHz Temperature -30℃-0℃ 1℃ ± (5% Reading + 3 Digits) 0℃-400℃ ± (1.0% Reading + 3 Digits) 400℃-1000℃ ± (2.0% Reading + 2 Digits) On-off Beep 100Ω 1Ω The resistance is not more than 50 built-in buzzer continuous sounding Diode 0.001V Display Approximate Diode Forward Voltage Value Other Parameters Sampling Rate About 3 Times/Sec Jaw Opening Maximum Size Approx. 25mm / 1in Display 5999 LCD Display Battery 2 x 1.5V AAA Battery (Not Included) Product Size 191 x 70 x 37 mm / 7.5 x 2.8 x 1.5 in Weight Approx. 405g / 14.3oz >>Please Click Here to Download the English User Manual<< Package Includes:   1 x Clamp Meter (Battery Not Included) 1 x English Instruction Manual 1 x One Pair Test Leads 1 x Thermocouple   Details Pictures:

ANENG AN8002 Digital True RMS 6000 Counts Multimeter AC/DC Current Voltage Frequency Resistance Temperature Tester ℃/℉
ANENG AN8002 Digital True RMS 6000 Counts Multimeter A... $31.76

Description:   It is a Auto-ranging digital MultiMate using double-integral style A/D transform as the core.  Can be used to measures Temperature AC/DC Voltage AC/DC Current Resistance Capacitance Diode and Continuity testing temperature Frequency and Etc. The products are battery powered they are characterized by stable function and high reliability, with the features of overload protection and LCD display for clear reading are an ideal tools for lavatory radio fans and family use.   Features:    Auto Range.  True RMS measurement.  Resistance capacitance frequency file high voltage 550V protection.  Large screen display, the maximum of 6000 words.  Sampling rate: about 3 times per second. Temperature measuring. Backlight display.  Data retention.  Polarity automatic recognition.  Low voltage display.  10A large current measurement MA level small current measurement Automatic shutdown.  Main measurement: AC / DC voltage, AC / DC current, resistance, capacitance.  Diode / off measurement, frequency and duty ratio measurement.    Specification:      Function Range Resolution Accuracy MAX.Value Other DC Voltage  6.000V 0.001V ±(0.5%+3) 1000V Input Resistance:10MΩ 60.00V 0.01V 600.0V 0.1V 1000V 1V 60.00mV    0.01mV 600mV 600.0mV     0.1mV    AC Voltage    6.000V 0.001V ±(1.0%+3) 750V Input Resistance:10MΩ(600mV range, >60MΩ) Frequency Response: 40Hz-1kHz 60.00V 0.01V 600.0V 0.1V 750V 1V 60.00mV 0.01mV    600mV 600.0mV     0.1mV    DC Current   6.000A 0.001A ±(1.2%+3) 10A MAX.Current: 10A(no more than 15 seconds) No Voltage input at this mode Frequency Response(AC):  40Hz-1kHz 10.00A 0.01A 60.00mA 0.01mA 600mA 600.0mA 0.1mA AC Current    6.000A 0.001A ±(1.5%+3) 10A 10.00A 0.01A 60.00mA 0.01mA 600mA 600.0mA 0.1mA Resistance 600.0Ω 0.1Ω ±(0.5%+3) 60MΩ No Voltage input at this mode 6.000kΩ 0.001kΩ 60.00kΩ 0.01kΩ 600.0kΩ 0.1kΩ 6.000MΩ 0.001MΩ 60.00MΩ 0.01MΩ ±(1.5%+3) Capacitance  9.999nF 0.001nF ±(5.0%+20) 9.999mF No Voltage input at this mode 99.99nF 0.01nF ±(2.0%+5) 999.9nF 0.1nF 9.999μF 0.001μF 99.99μF 0.01μF 999.9μF 0.1μF 9.999mF 0.001mF ±(5.0%+5) Frequency 99.99Hz 0.01Hz ±(0.1%+2) 9.999MHz   999.9Hz 0.1Hz 9.999kHz 0.001kHz 99.99kHz 0.01kHz 999.9kHz 0.1kHz 9.999MHz 0.001MHz Duty Cycle 1%~99% 0.1% ±(0.1%+2)     Diode √(DC forward current is 5mA, voltage is 3V) No Voltage input at this mode Continuity √(no more than 50Ω) Temperature   -20~1000℃ 1℃ ±(2.5%+5) 1000℃   -4~1832℉ 1℉ 1832℉ Measurement mode: double-integral style A/D transform  Sample rate: 3 times per second  Over range indication: OL Powered by 2 x AAA batteries  (Not included). Working Environment: 0-40 degrees relative humidity: <80%  Product size: approx. 130 x 65 x 30mm/5.11 x 2.55 x 1.18''  Net weight: approx. 170g  Gross weight: approx.238g            Good News !   ANENG AN113D the upgrade version of ANENG AN8002 has already released. This new product not only has the Manual gear as AN8002,but also added an automatic measurement button which is more convenient measurement and more friendly operation for the novices. Annnnd,It also equipped with a Black EBTN Screen, which can be clearly displayed without backlighting!!! More Details Please Click>>>   Package included:   1 x ANENG AN8002 Digital Ture RMS 6000 Counts Multimeter 2 x Test Lead Set  1 x Temperature Sensing Cable  1 x Storage Bag  1 x English User Manual Detail Pictures:                       , , , , , , , , ,

DS212 Digital Storage Oscilloscope Portable Nano Handheld Bandwidth 1MHz Sampling Rate 10MSa/s Thumb Wheel
DS212 Digital Storage Oscilloscope Portable Nano Handh... $149.60

Features:    With thrumbwheel adjust key  Pocket-sized digital storage oscilloscope meets basic electronic engineering requirements.  Dual trace three lines, new kind of system interface, capacitive convenient operation.  You can easily operate it with the gestures of one-click, double-click, press and slide.  The aluminum shell is very fashionable equipped with 320*240 color display, 8M  Memory card (USB flash disk), and chargeable Lithium batteries. The thickness is about 11 mm/ 0.43 inch only! The volume is small enough to take it anywhere.  It can meet the demands in many fields, such as, school experiments, electronic repairing, and electric engineering.    Specifications:   Model: DS212 MCU: STM32F303VC ADC: MCU internal ADC Channels: 2 analog channels, 1 operation channel Analog Bandwidth: 1 MHz Max Sample Rate: 10 MSa/s Max Sample Memory Depth: 8K Horizontal Sensitivity: 1uS/div to 2S/div (1-2-5 step) Vertical Sensitivity: 20mV/div to 10V/div (1-2-5 step) Analog Input Impedance: 1 MΩ Coupling: DC/AC Trigger Mode: ascend/descend edge trigger mode Math Waveforms: -A, -B, A+B, A-B, RecA, RecB, RecC Inbuilt Signal Generator: sine/square/triangle/sawtooth wave Synchronous Mode: auto, normal, single, none, scan value/average Storage: 8 MB flash disk memory APP Installed: 2 Operation: Button, Wheel button USB Port: Micro USB Battery: 500 mAh Screen Type: TFT LCD Screen Size: 2.8" Screen Resolution: 320 x 240 Dimension: 100 x 56.5 x 10.7 mm Weight (with battery): 90 g  Open Source: application layer open-source   Package Includes:   1x DS212 Mini Oscilloscope 1x Battery(built in) 2x Probes(with X1X10) 1x MicroUSB 1x Hex Key 1x Safety Instruction Note: the package Includes has been updated on 2019.6.27th.                  

FY8300S-20MHz/40MHz/60MHz Signal Generator Signal-Source-Frequency-Counter DDS Arbitrary Waveform Three-Channel Signal Generator
FY8300S-20MHz/40MHz/60MHz Signal Generator Signal-Sour... from $259.34

Features: This manual applies to each model of FY8300S series Function/Arbitrary Waveform Signal Generator. The last three characters of the model indicate the up limit output of Sine Wave (MHz). For example, the “60M” of the Model Number “FY8300-60M” indicates the Sine wave maximum output frequency is up to 60MHz.   FY8300S series Three-channel Function / Arbitrary waveform generator is a set of Function Signal Generator, Arbitrary Waveform Generator, Pulse Generator, Analog / Digital modulator, Sweep, Counters and Frequency Meter and other functions in a high Performance, cost-effective, multi-function signal generator. Abundant shortcut keys and graphical user interface simplifies every operation. Users do not have to spend a lot of time to learn and familiar with the operation of the instrument, you can be skilled use. For education, research and development, production, testing, maintenance and other industries to provide a new choice.   The instrument adopt the Direct Digital Synthesizer (DDS) technology and provide stable, precise, pure and low distortion signals. Surface mounting technology improves interference immunity and operational life span. Can output up to 97 groups of functions / arbitrary waveform, contains 33 groups of preset waveforms and 64 groups of user-defined waveforms. Preset waveforms: Sine, Square, Rectangle (Duty Cycle adjustable), Pulse (Pulse width and cycle time can be set accurately), Triangle/Ramp, CMOS(0~12V), Four channels TTL, Exponential Rise, Exponential Fall, Noise, ECG, DC etc.   Specification:   Frequency Model FY8300S-20M    FY8300S-40M FY8300S-60M Sine 0~20MHz 0~40MHz 0~60MHz Square 0~20MHz 0~20MHz 0~25MHz Ramp, Triangle 0~10MHz 0~10MHz 0~10MHz Pulse 0~10MHz 0~10MHz 0~10MHz TTL/CMOS 0~10MHz 0~10MHz 0~10MHz Arbitrary Waveform 0~10MHz 0~10MHz 0~10MHz Minimum pulse width 20ns(All models of pulse wave minimum width can reach 20ns) Min. Resolution on all frequency range 1μHz (Min. resolution can reach 1μHz on all frequency range to ensure adjusting accuracy under high frequency. For example, it can output 10.000000000001MHz signal). Accuracy ±20ppm Stability ±1ppm/ 3hours Waveform Characteristics Waveforms Sine, Square, Rectangle (Duty Cycle adjustable), Pulse (Pulse width and cycle time can be set accurately), Triangle/Ramp, Sawtooth Wave, CMOS, Four channels TTL, DC, Half wave, Full wave, Positive Step, Inverse Step, Positive Exponent, Inverse Exponent, Lorenz Pulse, Multitone, Noise, ECG, Trapezoidal Pulse, Sinc Pulse, Narrow Pulse, Gauss White Noise, AM, FM, and other 64 sets customer-defined waveform. Non-Volatile Storage Can store 64 user-defined arbitrary waveforms, (8K 14bits) * 64 Waveform Length 8192 points * 14bits Sampling Rate 250MSa/s Vertical Resolution 14 bits Sine Harmonic Suppression ≥50dBc(<1MHz); ≥45dBc(1MHz~20MHz); Total Harmonic Distortion <0.5% (20Hz~20kHz,0dBm) Rectangle Rise/Fall Time ≤15ns (VPP<5V) Overshoot ≤5% Duty Cycle 0.01%~99.99% (Resolution 0.01%) Sawtooth wave Linearity >99% (0.01Hz~10kHz) Output characteristics Amplitude ( VPP ) Frequency≤5MHz: 1mVpp~24Vpp; 5MHz 10MHz Frequency>20MHz: 1mVpp~5Vpp; Resolution 1mV Amplitude Stability ±0.5%/ 5 Hours Amplitude flatness ±2.5%(<10MHz);±5%(>10MHz); Waveform Output Impedance 50Ω±10% ( Typical ) Protection All channels can work more than 60 seconds when the load is short-circuited. DC Offset Offset Range Frequency≤20MHz: ±12V;  Frequency>20MHz: ±2.5V; Offset Resolution 1mV Phase Feature   Phase range 0~359.99° Phase resolution 0.01° TTL Output   TTL Level Amplitude >3Vpp Fan-out >8 TTL LOAD Rise/Fall Time ≤10ns CMOS Output Low Electric Level <0.3V High Electric Level 1V~12V Rise/Fall Time ≤18ns External Measurement Function Frequency, Period, Positive/Negative Pulse Width, Duty Cycle Input Voltage Range 1Vpp~20Vpp Frequency Meter Resolution 0.01Hz (Gate Time = 100S) Range 0.01Hz~100MHz Sensitivity Gate Time 3 grades (1S, 10S, 100S) adjustable Counter Range 0-4294967295 Coupling DC Working Mode Manual Period Measurement Range 5ns ~ 20s DC coupling measurement Pulse Width Measurement Range 0ns ~ 20s Resolution 5ns Duty Cycle Range (Display) 0% ~ 100% Sweep Carrier Waveform Sine, Square, Ramp, Arbitrary (except DC) Sweep Type Linear or Logarithm Sweep Direction Up, Down and roundtrip sweep directions; Sweep Objects Frequency, Amplitude, Offset, Duty Cycle Sweep Time 0.01S~999.99S/Step Setting range Starting position and Finishing position can be set arbitrarily. Sweep Range Decided by Parameters setting. VCO (Voltage Control Output) Modulation signal range to input 0~5V VCO signal frequency range 0-1000Hz VCO control object voltage controlling frequency (VCF), voltage controlling amplitude (VCiA), voltage controlling offset, voltage controlling duty cycle. VCO special function Can Amplitude Modulate (AM) or Frequency Modulate (FM) by external analog signal. Modulation Modulation Type AM, FM, PM, ASK, FSK, PSK Carrier Waveform Sine, Square, Triangle, Ramp, Arbitrary waveform (Except DC) AM Source Internal (CH2) / External (VCO IN Port) Modulating Waveform Sine, Square, Triangle, Ramp, Arbitrary waveform Depth 0% to 120% Modulating Frequency Internal : 1μHz~1MHz;  External: 1μHz~2KHz; FM Source Internal (CH2) / External (VCO IN Port) Modulating Waveform Sine, Square, Triangle, Ramp, Arbitrary waveform Modulating Frequency Internal : 1μHz~1MHz;  External: 1μHz~2KHz; PM Source Internal (CH2) / External (VCO IN Port) Modulating Waveform Sine, Square, Triangle, Ramp, Arbitrary waveform Phase Deviation 0° to 360° Modulating Frequency Internal : 1μHz~1MHz;  External: 1μHz~2KHz; ASK Source Internal (CH2), External (ASK IN Port), Manual Modulating Waveform Square with 50% duty cycle. Key Frequency 1μHz~10MHz FSK Source Internal (CH2), External (FSK IN Port), Manual Modulating Waveform Square with 50% duty cycle. Key Frequency 1μHz~10MHz PSK Source Internal (CH2), External (PSK IN Port), Manual Modulating Waveform Square with 50% duty cycle. Key Frequency 1μHz~10MHz Burst Function Carrier Waveform Sine, Square, Ramp, Arbitrary (except DC) Burst Count 1~1048575 Trigger Source Manual, Internal, External (AC/DC) General Specifications Display Type 2.4 inch, TFT Color Display. Save & Load Amount 12 Position 01 to 12 (01 for start default value) Interface Type USB to Serial interface Protocol Command line mode, providing communication protocols. Communicating Speed 115200bps (Industrial standard) Power Voltage Range AC100V~240V Technic SMD, LSI, Reliable and durable Buzzer Can be turned on/off by setting. Operation Buttons and knob continuously. Environment Temp.: 0~40℃, Humidity: <80% Size 200mm * 190mm * 90mm (L * W * H) Weight 700g Package Size 25cm * 21cm * 10cm (L * W * H) Package Weight 1.1kg(Main engine, accessories and packing materials)   >>Please Click Here to Download the English User Manual<< Package includes: 1 X FY8300S Signal Generator(20MHz/40MHz/60MHz)   Details pictures: 

DM8145 4 7/8 Bench top Multimeter 1000V 20A 80000 Counts Digital Multimeter tester Auto Range Multimetro Digital Voltmeter Ohm
DM8145 4 7/8 Bench top Multimeter 1000V 20A 80000 Coun... $304.72

Description: The Professional Bench Top Multimeter is a unique multi-functional device that has 4 7/8 digits Dual Display with 80,000 counts and Analog Bar Graph with 23 segments. This precision LCR meter is a cost-effective solution for component and material measurement. Measure speed is about 3 per second and with more than 50 measuring functions including DC/AC Voltage, DC/AC Currents, Resistance (Ω), Capacitance, Frequency (Hz), Rotational Speed, Square Waveform, Temperature (C/F), Duty Cycle, Diode and Continuity Check. Moreover, you can connect it to your computer through RS-232 Cable. The meter can provide functions including analog bar and unit symbol display, data holding, relative value measuring and maximal/minimal value measuring. This multimeter is most suitable for use on production lines, laboratories, factories, radio-technology, R & D, maintenance and repairing work. The meter can provide functions including analog bar and unit symbol display, data holding, relative value measuring and maximal/minimal value measuring. Features: High contrast and Wide visual angle LCD display with backlight Dual Display:  Main Display: 80000 Secondary Display: 80000 Analog Bar Graph: 23 segments, update 40 time/sec More than 50 measuring functions including DC/AC Voltage, DC/AC Currents, Resistance (Ω), Capacitance, Frequency (Hz), Temperature (°C/°F), Duty Cycle, Diode & Continuity Check Single Analyzed: (AC+DC) measuring synchronous (AC+Hz) measuring synchronous (DC+dBm) measuring synchronous (dBm+Hz) measuring synchronous (Hz+Duty) measuring synchronous (°C+°F) displaying synchronous Frequency measurement : 0.5Hz -1000.000000MHz Basic DC Accuracy : 0.05 % mV Impedance : >1000MΩ 16 Frequency points, 1% to 99% duty selectable square wave output Analyzing component of current or voltage signal Resistance Measuring : 0.1Ω to 80MΩ,10MΩ to 8000MΩ  Capacitance Measuring : 1nF to 100µF Temperature Measuring : -50°C to 1372°C, -58°F to 2502°F dBm 20 types of reference impedance Auto data hold/ peak hold Relative measuring : REL, Relative percent : REL% 36 hours dynamic recording : MAX / MIN / average/ MAX-MIN Communication : 9-pin isolated optical RS232 cable Measure speed is about 3 per second Timer for measurement Safety/Compliance : IEC 61010 CAT II 1000V ; CAT III 600V Auto power off 0.1 ~ 99.9% pulse duty cycle measuring Set upper and lower limit area measuring Photoelectricity insulation RS-232 computer interface Timing measuring function AC measuring adopt High accuracy RMS, Widely measuring and AC+DC function, can measure the accuracy virtual value of AC by any wave Specifications: Basic function Range Accuracy DCV 80mV/800mV/8V/80V ±(0.05% rdg+5) 800V/1000V ±(0.08% rdg+10) ACV 80mV/800mV/8V ±(0.8%~8.0%rdg+50) 80V ±(0.8%rdg+50) 750V ±(0.8%~5.0%rdg+50) DCA 80mA/800mA ±(0.2% rdg+10) 8A/20A ±(0.5% rdg+10) ACA 80mA/800mA 50Hz~5kHz±(0.2% rdg+10) 8A/20A 50Hz~200Hz±(0.5% rdg+10) Resistance 800Ω ±(0.3% rdg+10) 8KΩ/80KΩ/800KΩ/8MΩ ±(0.3% rdg+5) 60MΩ 0Ω~40MΩ: ±(2.5% rdg+10)40MΩ~80MΩ: ±(3.5% rdg+10) dBm ‘-80.00dBm~+80.00dBm ±1.0% rdg Frequency 1000Hz/10KHz/100KHz/1000kHz/6MHz ±(0.5% rdg+5) 10MHz/100MHz/1000MHz ±(0.1% rdg+5) Capacitance 1nF ±(5.0% rdg+50) 10nF/100nF/1uF/10uF/100uF ±(2.5% rdg+50) Diode 3.0000V ±(3.0% rdg+5) Temperature -50°~1300°/-58°~2372° ±(1.5% rdg+10) Maximum voltage between any terminal and earth ground: 1000V RMS Continuity Beeper: 3kHz Approx. Operating Temperature: 0°C to +50°C  Storage Temperature : -20°C to +60°C Operating Altitude: under 2000m  Storage Altitude : under 10,000m Relative Humidity :  ≤75% at 0°C to +40°C Electromagnetic Compatibility : in a RF field or 1 V/m on all ranges and function except Capacitance Total Accuracy : specified +5% of range Capacitance not specified in RF fields performance above 1 V/m is not specified PC Interface : RS-232 Compatible with Windows 2000 & XP only AC Power : 110~220 V ( EU Power adapter plug) Size : approx. 242 x 212 x 98 mm Weight : approx.1388g (accessories not included) Package Includes: 1 x Digital Bench Top Multimeter 1 x Pair of Test Leads 1 x Type K Thermocouple 1 x RS-232 Software CD 1 x 9-pin Cable Adapter 1 x AC Power Cord (EU Plug) 1 x English Instruction Manual 1 x Standard Packaging Box Note: We will send you a plug adapter according to your country. Details Pictures:

ANENG SZ18 9999 Counts Professional True RMS Digital Multimeter Analog Tester Multimetro DIY Square Wave Output Transistor Capacitor NCV Testers
ANENG SZ18 9999 Counts Professional True RMS Digital M... $74.13

Features: ANENG SZ18 is an automatic range digital multimeter with 9999 words with a true effective value. The instrument is full-key operation with triple display. With square wave output function Measure AC voltage and DC voltage Measure AC and DC current Measuring resistance/temperature Test continuity and diode Measuring capacitance/NCV Measuring frequency and duty cycle Anti-interference AC voltage detection Including 16 in 1 combination test accessories and a storage bag Specifications: Brand ANENG Model SZ18 Liquid crystal Display (LCD) 9999 Range Automatic / manual Material ABS + TPE Sampling rate 3 times / sec True RMS Yes Data retention Yes Screen backlight Yes Low battery warning Yes Automatic shut-down Yes Battery Type 3 * 1.5v AA battery (not included) Characteristics Range Accuracy AC frequency response DC Current 9.999A/999.9mA ±(1.0% + 3) - DC Current 99.99mA/9.999mA/99.99 μA/999.9μA ±(0.8% + 3) - AC Current 9.999A/999.9mA ±(1.2% + 3) 40hz~1khz AC Current 99.99mA/9.999mA/99.99 μA/999.9μA ±(1.0% + 3) 40hz~1khz DC Voltage 999. 9mv/9.999v/99.99v/999.9v/9. 999mv/99. 99mv/999.9mv ±(0.5% + 3) - AC Voltage 999. 9mv/9.999v/99.99v/750.0v/9. 999mv/99. 99mv/999.9mv ±(1.0% + 3) 40hz~1khz Resistance 99.99Ω ±(1.0% + 3) - Resistance 999.9Ω/9.999k Ω/99.99k Ω/999.9kΩ ±(0.5% + 3) - Resistance 9.999MΩ ±(1.5% + 3) - Resistance 99.99MΩ ±(3.0% + 5) - Capacitance 9.999nF ±(5.0% + 20) - Capacitance 99. 99nf/999. 9nf/9.999μf/99.99μf/999.9 μf ±(2.0% + 5) - Capacitance 9.999mF ±(5.0% + 5) - Frequency 99.99hz/999.9hz/9.999khz/99.99khz/999.9khz/5.000mhz ±(0.1% + 2) - Temperature (-20 ~ 1000)℃ / (-4 ~ 1832)℉ ±(2.5% + 5) - Duty cycle 1% ~ 99% Diodo Yes On /off Yes NCV Yes Working environment Temperature 0 ~ 40 ℃     Humidity <75% Package included: 1 * SZ18 digital multimeter  2 * Test lead wire 1 * Thermocouple 1 * Manual 1 * Bag  1 * 16 in 1 combination line  >>Please click here to download the English user manual<< Details pictures:

MINI DS213 Digital Storage Oscilloscope Portable 15MHz Bandwidth 100MSa/s  Sampling Rate 2 Analog Channels+2 Digital Channels 3 Inch Screen With Logic Trigger
MINI DS213 Digital Storage Oscilloscope Portable 15MHz... $262.83

Description: DS213 is a “5-track, 4-wave line” digital storage oscilloscope for g'eneral-purpose electronic engineering task and it is based on ARM Cortex M3 core. DS213 uses FPGA to manage external ADC’s control and data cache mode. It provides 4 application partitions for loading and upgrading up to 4 different application firmware. It also has built-in 8MB USB flash drive for storing waveforms and upgrading system firmware. The oscilloscope code application layer is open source, and users can develop oscilloscope firmware according to their needs   Features: Mini size, light weight, portable and handheld; It can store waveforms, making waveform analysis clearer and more effective; Multiple trigger modes, support Ascend/Descend Edge Trigger, Positive/Negative Pulse Trigger, and Logic Trigger; Powerful ability to process waveforms, it can automatically measure parameters such us voltage, frequency and pulse width.   Specifications: CPU: ARM Cortex M3 FIFO & Control: FPGA ADC: HWD9288-100 Analog Channels: 2([CH_A] [CH_B]) Digital Channels: 2([C_C] [CH_D]) Operation Channel: INV [CH_A], INV [CH_B], [CH_A]+[CH_B], [CH_A]-[CH_B],[C_C]&[CH_D],[C_C] | [CH_D] Vertical Sensitivity: 10mV-10V/div (1-2-5 STEP) (using X1 probe)                 100mV-100V/div (1-2-5 STEP) (using X10 probe) Vertical Resolution: 8 bits Sample Memory Depth: 4 channels, 4*4K Coupling: DC, AC Max Input Voltage: ±40Vpp (using X1 probe)                  ±400Vpp (using X10 probe) Trigger Types: Ascend/Descend Edge Trigger Mode, Positive/Negative Pulse Trigger, Logic Trigger Trigger Mode: Auto, Normal, Single, Slow Trigger Source: [CH_A] [CH_B] [C_C] [CH_D] Signal Source: Square Wave: 10Hz to 8MHz, in total 20 shif1ts and 3 Vpp Signal Sources; Sine/Triangle/Sawtooth Wave: 10Hz to 20MHz, in total 11 shif1ts and 3 Vpp Signal Sources Storage: built in 8M USB disk File Types: BMP,BUF,CSV Auto Measurement Types: Signal sequence/cycle/duty ratio, p'eak voltage/virtual value/max value/min value/average Cursor Measurement: Time value, Amplitude value Display Modes: 4 wave lines: Line 1: [CH_A], HIDE Line 2: [CH_B], HIDE Line 3: [C_C], REC_1, REC _2, REC _3, REC _4, HIDE Line 4: [CH_D], [CH_A]+[CH_B], [CH_A]-[CH_B], [C_C]&[CH_D], [C_C] | [CH_D], HIDE Sampling Mode: Real-time Sampling Sampling Rate: 100M Sa/s Battery: 1000mAh Size: 99.5mmx58.5mmx13.5mm Weight: 129g (with battery) Certificate: CE, FCC Package Includes: 1 x DS213 oscilloscope(not include the silicone case) 2 x Test Proes 1 x one Set of accessories The silicone case is not included in the package ,you can click the link below to buy it  ►Silicone Case for DS213 : 4 colors for choice /with Round stand Details Pictures:

ANENG AN113D Intelligent  Auto Measure True- RMS Digital Multimeter 6000 Counts Resistance Diode Continuity Tester Temperature AC/DC Voltage Current Meter Upgraded from AN8002
ANENG AN113D Intelligent Auto Measure True- RMS Digit... $31.26

Good News! ANENG AN113D the upgrade version of ANENG AN8002 has already released. This new product not only has the Manual gear as AN8002,but also added an automatic measurement button which is more convenient measurement and more friendly operation for the novices. Annnnd,It also equipped with a Black EBTN Screen, which can be clearly displayed without backlighting!!! Features: This product is a multi-functional, auto-ranging digital multimeter with a 6000 counts LCD display.  1. Measurement functions include AC/DC voltage, AC/DC current, resistance, diode test/continuity, NCV, frequency/duty cycle, capacitance.  2. Support True- RMS  3. Support Auto Power Off  4. Support temperature measurement  5. Support data hold   Specification : Display(LCD): 6000 counts Ranging :Auto  Material: ABS/PVC Update Rate: 3 times / second Low Battery Indication: √ Product Weight :114g (batteries not included) Product Dimension :130*65*32mm OperatingStorage: Temperature 0~40℃ Humidity <75% OperatingStorage :Temperature -20~60℃ Humidity < 80% DC Voltage : 6.000V (0.001V) / 60.00V( 0.01V)/ 600.0V (0.1V )/1000V (1V) ±(0.5%+3) DC Voltage : 60.00mV (0.01mV)/ 600mV (0.1mV) ±(0.5%+3)  AC Voltage : 6.000V (0.001V) / 60.00V (0.01V)/ 600.0V (0.1V)/ 750V (1V ) ±(1.0%+3)  AC Voltage : 60.00mV (0.01mV) / 600.0mV (0.1mV) ±(1.0%+3)  DC Current : 6.000A (0.001A) / 10.00A( 0.01A) ±(1.2%+3)  DC Current : 60.00mA (0.01mA)/600.0mA (0.1mA)  AC Current : 6.000A (0.001A) /10.00A (0.01A) ±(1.5%+3) AC Current : 60.00mA (0.01mA)/ 600.0mA (0.1mA) ±(1.5%+3) Resistance : 600.0Ω (0.1Ω)/6.000kΩ(0.001kΩ)/60.00kΩ (0.01kΩ) /600.0kΩ(0.1kΩ) / 6.000MΩ (0.001MΩ) ±(0.5%+3) /60.00MΩ (0.01MΩ) ±(1.5%+3)  Capacitance : 9.999nF(0.001nF) ±(5.0%+20) /99.99nF(0.01nF) 999.9nF(0.1nF)/ 9.999μF (0.001μF)/ 99.99μF(0.01μF)/ 999.9μF (0.1μF)±(2.0%+5) / 9.999mF (0.001mF) ±(5.0%+5)  Frequency : 99.99Hz (0.01Hz) /999.9Hz (0.1Hz)/ 9.999kHz (0.001kHz)/ 99.99kHz (0.01kHz)/ 999.9kHz (0.1kHz)/ 9.999MHz (0.001MHz) ±(0.1%+2)  Duty Cycle 1%~99% 0.1% ±(0.1%+2)  Temperature (-20~1000)℃ 1℃ ±(2.5%+5 ) 1000℃ (-4~1832)℉ 1℉ 1832℉ Diode: √ Continuity :√ >>Please Click Here to Download the English User Manual<< Package Includes: 1 x Multimeter 1 x Pair of test leads 1 x Thermocouple 1 x English user manual   Details Pictures: 

HackRF One RTL SDR Software Defined Radio USB Platform Reception of Signals 1MHz to 6GHz Software Demo Board Kit Dongle Receiver with Antenna
HackRF One RTL SDR Software Defined Radio USB Platform... $242.48

HackRF One is the current hardware platform for the HackRF project. It is a Software Defined Radio peripheral capable of transmission or reception of radio signals from 1 MHz to 6 GHz. Designed to enable test and development of modern and next generation radio technologies, HackRF One is an open source hardware platform that can be used as a USB peripheral or programmed for stand-alone operation.   Features:   half-duplex transceiver operating freq: 1 MHz to 6 GHz supported sample rates: 2 Msps to 20 Msps (quadrature) resolution: 8 bits interface: High Speed USB (with USB Micro-B connector) power supply: USB bus power software-controlled antenna port power (max 50 mA at 3.3 V) SMA female antenna connector (50 ohms) SMA female clock input and output for synchronization Convenient buttons for programming Pin headers for expansion Portable Open source   Note: very prefessional product, pls be sure you know what it is and how to use it.   Package includes:   1 X Receiver Kit   Details pictures:                     

ANENG ST209 Digital Multimeter Clamp Meter 6000 Counts True RMS Amp DC/AC Current Clamp Tester Meters Voltmeter 400V Auto Range
ANENG ST209 Digital Multimeter Clamp Meter 6000 Counts... $49.89

Feature   1-1. Display: liquid crystal display (LCD); 1-2. Maximum display: 5999 (3 5/6) bit automatic polarity display; 1-3. Measurement method: double integral A/D conversion; 1-4. Sampling rate: about 3 times per second; 1-5. Overrange display: The highest position shows“OL”; 1-6. Low voltage display:“Low voltage symbol ”symbol appears; 1-7. Working environment:(0 ~ 40)°,relative humidity < 80%; 1-8.Power: AAA 1.5V battery(not  include);   Functional parameters Function   DC voltage  DCV ▲ AC voltage  ACV ▲ DC current  DCA ▲ AC current  ACA ▲ Resistor / Diode / On-Off Test / Capacitor  ▲ Frequency F ▲ Square wave output ▲ NCV ▲ Zero line /Fire line test   Full unit symbol ▲ Backlight manual/Auto off ▲ True RMS measurement ▲ Temperature(°/°) ▲ Flashlight lighting ▲ Technical Specifications: Package Includes: 1 x ST209 Clamp Meter 1 x Storage Bag 1 x English User Manual 1 x Pair of Test Leads 1 x Type K Thermocouple   NOTE:   This series of instruments is designed in accordance with IEC1010 (Safety Standards promulgated by the International Electrotechnical Commission), please read the safety precautions before use. 1. When measuring voltage, please do not input the limit voltage exceeding the effective value of DC 1000V or AC 750V; 2.The voltage below 2.36V is a safe voltage. When measuring higher than 36V DC and 25V AC voltage, check whether the test leads are in reliable contact, are connected correctly, and are well insulated to avoid electric shock; 3. When changing functions and ranges, the test leads should leave the test point.. Details Pictures:

Hantek 2C42 Digital Oscilloscope + Multimeter Portable USB 2 Channels 40mhz
Hantek 2C42 Digital Oscilloscope + Multimeter Portable... $207.94

Overview:   Digital oscilloscope +multimeter, all in one! AUTO one-key test + cursor measurement function! 4000 counts universal multimeter function! A real professional and magic scope! buy one and no need buy more equipments!   Features: ♦ Oscilloscope + Multimeter:  This multi-purpose station own three universal test instrument functions. It is outgoing right-hand product for engineers. ♦  Intelligent charging control: Its lithium batteries can be recharged byeither high current-5V/2A or ordinary computer USB interface. Allow while charging, while using, very convenient and handy; ♦ Ultra-low power design:  Type C charging interface, after every recharge of 2 hours, the device can be used continuously for a full day or standby more than two months; ♦  Large-capacity lithium battery power supply:  Tesla style 18650 replaceable lithium battery power system, free from replace battery; ♦  5V/2A charger + Type C charging cable: Type C power + data transfer interface,  can share the charger and data cable with your mobile phone; ♦  AUTO one-key test:  Magic tool and essential function for test newbie; ♦  Volume small, one hand holding: The 45 degree suspension bracket design provide you a work station anywhere anytime; ♦  One key page out, quick compare two groups of reference waveforms + 6 groups of waveforms storage, simple and effective; ♦  Digital voltmeter function: automatic frequency and amplitude measurement, convenient and worry-free; ♦  Its cursor measurement function supports time and voltage manual measurement, and measure the required waveforms accurately; ♦  Color LCD screen: exquisite and smooth lines make the waveforms clear and undistorted when magnify; ♦  Minimalist keyboard design simplify operation, convenient to use; ♦  Unibody casing: fine touch feeling, favorable impact resistance, outstanding heat resistance, easy to disassemble; ♦ Self-calibration function : free from level drift after long time unused; ♦  Universal multimeter function: voltage, current, resistance, diode, capacitor, on-off test;       Specification: Model: Hantek2C42 Channel: 2 CH+DMM Bandwidth: 40MHz Sample: 250MSa/S Power: Direct charge DMM: √  Package Includes: 1 x Digital Oscilloscope 1 x Probe 2 x Clip Probe 1 x Charging cable 1 x Power adapter 1 x Multimeter Probe    Details Pictures:

FY6800 2-Channel DDS Arbitrary Waveform Signal Generator 14bits 250MSa/s Sine Square Pulse Frequency Meter VCO Modulation
FY6800 2-Channel DDS Arbitrary Waveform Signal Generat... from $0.00

Description : FY6800 series Dual-channel Function / Arbitrary waveform generator is a set of Function Signal Generator, Arbitrary Waveform Generator, Pulse Generator, Analog / Digital modulator, VCO, Sweep, Counters and Frequency Meter and other functions in a high Performance, cost-effective, multi-function signal generator. Abundant shortcut keys and graphical user interface simplifies every operation. Users do not have to spend a lot of time to learn and familiar with the operation of the instrument, you can be skilled use. For education, research and development, production, testing, maintenance and other industries to provide a new choice.       The instrument adopt the Direct Digital Synthesizer (DDS) technology and provide stable, precise, pure and low distortion signals. Surface mounting technology improves interference immunity and operational life span. Due to communications with extensive users and fully understanding to users’ practice, we regard users’ demand as the most important factor in R&D. Continuously innovatio'n and listening users’ suggestions, we try to offer customers better products with higher cost performance.   Features : Adopt the Direct Digital Synthesizer (DDS) technology and provide stable, precise, pure and low distortion signals.  Adopt ABS plastic shell with table type design. Use 100-240V (AC) wide range voltage power supply.  Standard 3-pin power plug adds ground protection. 2.4 inch TFT Color LCD with 320×240 resolution, displaying parameters and graphics of the two channels at the same time. The instrument uses 14-bit high-speed D/A converter chip (5Vpp output quantization error is less than 1mV), 250MSa/s sample rate, 14bits vertical resolution. Can output up to 97 groups of functions / arbitrary waveform, contains 33 groups of preset waveforms and 64 groups of user-defined waveforms. Preset waveforms: Sine, Square (Duty Cycle adjustable), Pulse (Pulse width and cycle time can be set accurately), Triangle/Ramp, CMOS(0~10V), Four channels TTL, Exponential Rise, Exponential Fall, Noise, ECG, DC etc. Enable to store 64 arbitrary waveform data files, each one of waveform storage depth 8192 points * 14bits;  Various modulation types: AM, FM, PM, ASK, FSK and PSK modulations. Sweep Function: It can sweep 4 properties of signals including frequency, amplitude, offset and duty cycle; It has Linear and Logarithm two sweep types; 0.01S~999.99S sweep time; Up, Down and roundtrip sweep directions. VCO Function (Voltage Control Output): Can be achieved by an external input signal: voltage controlling frequency, voltage controlling amplitude, voltage controlling offset, voltage controlling duty cycle and PWM modulations. Burst Output Function: There has Manual Trigger, internal CH2 Trigger, and External Trigger for your options. It can output 1~1048575 pulse trains. 100M Frequency meter function: It can measure frequency, period, pulse width and duty cycle. Max. frequency workable is 100MHz and Min. frequency workable is 0.01 Hz. Counter Function: It has 2 coupling measure modes including DC coupling and AC coupling. This design can solve inaccuracy problem of AC coupling. Standard dual full functional channels which are equivalent to two independent generators. Channel SYNC Function: Support waveform copy and state copy between channels. Support two or more signal generators connected to achieve multi-channel output, the maximum support 16-channel synchronous output, the phase between each channel can be adjusted.  Precisely adjust the phases of the two channels, Precision can be 0.01°. Minimu'm amplitude resolution can be up to 1 mV. Amplitude range is 0~20Vpp. Duty-cycle of each channel can be adjusted independently0.01%-99.99%, the adjusting resolution is 0.01%. -10V to +10V DC Offset function. Resolution 0.001V. Save function: It can save 20 sets user-set parameters and can be loaded at anytime. Communicating function: All functions can be controlled by PC program and the communication protocol is open for secondary development. Output short-circuit protection: All channels can work more than 60 seconds when the load is short-circuited. Provide powerful waveform editing PC software. It supports user defined waveform editing and visual control of various parameter indicators.  Can choose our FYA2000S series or FPA1000 series power amplifier to output 20W~100W signal in DC-10MHz width without any distortion. Advantage 1. FY6800 user interface displays the parameters and waveforms of the two channels at the same time. Each function has a separate user interface, different contents will be displayed when different functions are enabled. 2. The instrument uses 14-bit high-speed D/A converter chip (5Vpp output quantization error is less than 1mV), 250MSa/s sample rate, 14bits vertical resolution. 3. Enable to store 64 arbitrary waveform data files, each one of waveform storage depth 8192 points * 14bits;  4. Various modulation types: AM, FM, PM, ASK, FSK and PSK modulations. 5. VCO Function (Voltage Control Output). 6. The minimu'm output amplitude is 1mV , minimu'm amplitude resolution can be up to 1mV.  7.Precisely adjust the phases of the two channels, Precision can be 0.01°. 8. Duty cycle of each channel can be adjusted separately. Precision can be 0.01%. 9. 4 Channel TTL Output. 10. Easy to use, powerful PC Software. Specification : Unless specified, all specifications can be guaranteed if the following two conditions are met. The generator has passed self-inspection.  The generator has been working continuously for at least 30 minutes under the specified temperature (18℃~28℃).  All the specifications are guaranteed unless those marked with “typical” .   Frequency Model FY6800-30M FY6800-60M Sine 0~30MHz 0~60MHz Square 0~20MHz 0~25MHz Ramp, Triangle 0~10MHz 0~10MHz Pulse 0~10MHz 0~10MHz TTL/CMOS 0~20MHz 0~20MHz Arbitrary Waveform 0~10MHz 0~10MHz Minimu'm pulse width 20ns(All models of pulse wave minimu'm width can reach 20ns) Min. Resolution on all frequency range 1μHz (Min. resolution can reach 1μHz on all frequency range to ensure adjusting accuracy under high frequency. For example, it can output 10.000000000001MHz signal). Accuracy ±20ppm Stability ±1ppm/ 3hours Waveform Characteristics Waveforms Sine, Square (Duty Cycle adjustable), Pulse (Pulse width and cycle time can be set accurately), Triangle/Ramp, Sawtooth Wave, CMOS, Four channels TTL, DC, Half wave, Full wave, Positive Step, Inverse Step, Positive Exponent, Inverse Exponent, Lorenz Pulse, Multitone, Noise, ECG, Trapezoidal Pulse, Sinc Pulse, Narrow Pulse, Gauss White Noise, AM, FM, and other 64 sets customer-defined waveform. Non-Volatile Storage Can store 64 user-defined arbitrary waveforms, (8K 14bits) * 64 Waveform Length 8192 points * 14bits Sampling Rate 250MSa/s Vertical Resolution 14 bits Sine Harmonic Suppression ≥50dBc(<1MHz); ≥45dBc(1MHz~20MHz); Total Harmonic Distortion <0.5% (20Hz~20kHz,0dBm) Square Rise/Fall Time ≤7ns (VPP<5V) Overshoot ≤5% Duty Cycle 0.01%~99.99% (Resolution 0.01%) Sawtooth wave Linearity >99% (0.01Hz~10kHz) Output characteristics Amplitude(VPP) Frequency≤10MHz: 1mVpp~20Vpp; 10MHz Frequency>20MHz: 1mVpp~5Vpp; Resolution 1mV Amplitude Stability ±0.5%/ 5 Hours Amplitude flatness ±2.5%(<10MHz);±5%(>10MHz); Waveform Output Impedance 50Ω±10% (Typical) Protection All channels can work more than 60 seconds when the load is short-circuited.  DC Offset Offset Range Frequency≤20MHz: ±10V;  Frequency>20MHz: ±2.5V; Offset Resolution 1mV Phase Feature   Phase range 0~359.99° Phase resolution 0.01° TTL Output   TTL Level Amplitude >3Vpp Fan-out >8 TTL LOAD Rise/Fall Time ≤10ns CMOS Output Low Electric Level <0.3V High Electric Level 1V~10V Rise/Fall Time ≤18ns External Measurement Function Frequency, Period, Positive/Negative Pulse Width, Duty Cycle Input Voltage Range 1Vpp~20Vpp Frequency Meter Resolution 0.01Hz (Gate Time = 100S) Range 0.01Hz~100MHz Sensitivity Gate Time 3 grades (1S, 10S, 100S) adjustable Counter Range 0-4294967295 Coupling DC, AC Working Mode Manual Period Measurement Range 5ns ~ 20s DC coupling measurement Pulse Width Measurement Range 0ns ~ 20s Resolution 5ns Duty Cycle Range (Display) 0% ~ 100% Sweep Carrier Waveform Sine, Square, Ramp, Arbitrary (except DC) Sweep Type Linear or Logarithm Sweep Direction Up, Down and roundtrip sweep directions; Sweep Objects Frequency, Amplitude, Offset, Duty Cycle Sweep Time 0.01S~999.99S/Step Setting range Starting position and Finishing position can be set arbitrarily. Sweep Range Decided by Parameters setting. VCO (Voltage Control Output) Modulation signal range to input 0~5V VCO signal frequency range 0-1000Hz VCO control object voltage controlling frequency (VCF), voltage controlling amplitude (VCA), voltage controlling offset, voltage controlling duty cycle. VCO special function Can Amplitude Modulate (AM) or Frequency Modulate (FM) by external analog signal. Modulation Modulation Type AM, FM, PM, ASK, FSK, PSK Carrier Waveform Sine, Square, Triangle, Ramp, Arbitrary waveform (Except DC) AM Source Internal (CH2) / External (VCO IN Port) Modulating Waveform Sine, Square, Triangle, Ramp, Arbitrary waveform Depth 0% to 100% Modulating Frequency Internal : 1μHz~1MHz;  External: 1μHz~2KHz; FM Source Internal (CH2) / External (VCO IN Port) Modulating Waveform Sine, Square, Triangle, Ramp, Arbitrary waveform Modulating Frequency Internal : 1μHz~1MHz;  External: 1μHz~2KHz; PM Source Internal (CH2) / External (VCO IN Port) Modulating Waveform Sine, Square, Triangle, Ramp, Arbitrary waveform Phase Deviation 0° to 360° Modulating Frequency Internal : 1μHz~1MHz;  External: 1μHz~2KHz; ASK Source Internal (CH2), External (ASK IN Port), Manual Modulating Waveform Square with 50% duty cycle. Key Frequency 1μHz~10MHz FSK Source Internal (CH2), External (FSK IN Port), Manual Modulating Waveform Square with 50% duty cycle. Key Frequency 1μHz~10MHz PSK Source Internal (CH2), External (PSK IN Port), Manual Modulating Waveform Square with 50% duty cycle. Key Frequency 1μHz~10MHz Burst Function Carrier Waveform Sine, Square, Ramp, Arbitrary (except DC) Burst Count 1~1048575 Trigger Source Manual, Internal, External (AC/DC) General Specifications Display Type 2.4 inch, TFT Color Display. Save & Load Amount 20 Position 01 to 20 (01 for start default value) Interface Type USB to Serial interface Protocol Comman'd line mode, providing communication protocols. Communicating Speed 115200bps Power Voltage Range AC100V~240V Technic SMD, LSI, Reliable and durable Buzzer Can be turned on/off by setting. Operation Buttons and knob continuously. Environment Temp.: 0~40℃, Humidity: <80% Size 200mm * 190mm * 90mm (L * W * H) Weight 1000g Package Size 25cm * 21cm * 10cm (L * W * H) Package Weight 1kg(Main engine, accessories and packing materials) Package includeds : 1 x FY6800 DDS Signal Generator (FY6800-30M/FY6800-60M for Optional~) 1 x Power Cable 1 x USB Data Cable 2 x BNC-Clip Cable (Signal output cable) 1 x BNC-BNC Cable (Signal output cable) 1 x Warranty Card   FY6800 series signal generator can not only use independently, but also through the serial port control, communication protocol open, PC software free of charge. The software has the function windows of the waveform window, the text window and the control window, and the simple and clear operation interface greatly improves the user operation experience. Control window   All functional operation intuitive display in the software interface, allowing users to intuitive and rapid adjustment of the instrument function parameters, greatly improve the ease of use of the instrument. Waveform window and text window has a powerful waveform editing function, can achieve 18 different parameters of any waveform superposition and modulation. Step wave the number of steps can be arbitrarily set between 2 - 4096; Triangle wave vertex positions can be set to realize Ramp waves with different slopes. The following figure shows the hand-painted arbitrary waveform, the instrument can support up to 8192 * 14bit arbitrary waveform, can effectively restore more waveform details, especially for medical and automotive maintenance in the field of the required signal simulation.   Performance Testing           , , , , , , , , ,

BSIDE ACM91 Digital AC/DC Current Clamp Meter Auto-Range Car Repair TRMS Multimeter Live Check NCV Frequency Capacitor Tester  Mustool MT866
BSIDE ACM91 Digital AC/DC Current Clamp Meter Auto-Ran... $69.47

Note: MUSTOOL MT866 has changed to BSIDE ACM91 from 2019/10/14. The Appearance has some differences but functions are the same. Description: Bside ACM91 TRMS AC/DC Clamp Meter Auto-Ranging 6000 Counts 0.001A Resolution Current Frequency Temperature Tester with Pocket Clip Design concept: function integration, test integration.   AC/DC voltage, AC/DC ampere, AC/DC Current (by jaw minimum 1mA), Temperature, Frequency, Capacitance, DC microampere, Resistance, LIVE wire check, voltage alert, with such a small size it meets the rules of the state has made the most perfect functions. LIVE wire check function and V ~ alert function conveniently quickly identify mains connection status.Display double line shows, can display voltage or current and frequency at the same time. LoZ, low impedance voltage detection, very suitable for maintenance industry We optimize the jaw, increased the pens and hustle, easy one-handed operation. We optimize jack position, better security and aesthetics, reduced the foreign body into the dust. We have added back hooks, convenient to carry Fetaures: Measure both DC current and AC current (minimum 1mA by jaws) Measure microamps μA (minimum 0.1μA by terminals) Measure AC and DC voltage Measure frequency Low impedance voltage measurement Measure resistance, continuity and capacitance Measure temperature Live check function V-alert measurement Clamp on frequency function Auto range Data hold Auto power off Back light Conform to the IEC-61010-1, IEC-61010-2-030, IEC-61010-2-032, IEC-61010-2-033 standards Over-voltage protection class CAT III 300V, CAT II 600V, pollution degree II Specification:   Color: Black Display: 6000 counts DC current: 6A/60A/100A 0.001A/0.01A/0.1A ±(3.0%+5counts) DC current(uA):0-200uA 0.1uA ±(0.8%+5counts) AC current: 6A/60A/100A 0.001A/0.01A/0.1A ±(2.5%+5counts) In 6A range, resolution is 0.001A, the test range is 0.001A~6A. In 60A range, resolution is 0.01A, the test range is 0.01A~60A. In 100A range, resolution is 0.1A, the test range is 0.1A~100A. DC voltage: 6V/60V/600V 0.001V/0.01V/0.1V ±(1.0%+3counts) AC voltage: 6V/60V/600V 0.001V/0.01V/0.1V ±(1.0%+3counts) Low impedance LOZ: Max 600V Resolution 0.1V Resistance: 600/6k/60k/600k/6M ohm 0.1/0.001K/0.01K/0.1K/0.001M ohm ±(1.0%+3counts) 60Mohm 0.01Mohm ±(1.2%+20counts) Capacitance: 600uF/6000uF 0.1uF/1uF ±(4.0%+3counts) Frequency: 60Hz/1000Hz 0.1Hz/1Hz ±(1.0%+5counts) Frequency(by jaws): 60Hz/1000Hz 0.1Hz/1Hz ±(1.0%+5counts) Buzzer: If the resistance is less than 30Ω, the continuity beeper sounds. Temperature: -20°C~500°C 1°C/2°F (2.0%+2counts) Jaw Capacity: 20mm Power: 1.5V (AAA) x 2 (not included) Size: 179mm x 67mm x 36 mm Weight: 137g   Package Included: 1 x Digital Clamp Meter 1 x Test Leads 1 x Thermocouple 1 x User Manual 1 x Carrying Case Detail Pictures:

FY6600 Digital 12-60MHz Dual Channel DDS Function Arbitrary Waveform Signal Generator
FY6600 Digital 12-60MHz Dual Channel DDS Function Arbi... from $164.59

Description:   1. The device uses professional 14 bit high speed D/A chip, 250MSa/s sampling rate. Active crystal oscillator as the benchmark makes the output waveform is more exquisite, stable and precise. Signal output range:1mVpp~20Vpp. 2. Bias level can be adjusted arbitrarily. Dual channel wave appears. practical VCO function. Every function has separete operation interface. The date displays succinct and clear, simple operation, convenient usage. 3. The FY6600 Series dual channel function/arbitrary waveform generator is a signal enerator that integrates function signal generator,pulse signal generator, sweeper meter, counter and frequency meter with high performance, cost performance, multi-function. 4. The device uses large scale FPGA integrated circuit and high peed MCU microprocessor. The internal circuit uses active crystal oscillator as the benchmark,high stablity. 5. Surface mount technology has greatly improved the anti-interference and service life of the instrument. 6. The device has the complete separate dual DDS signal and TTL level output. It is not only for the user to preset 33 commonly used waveform signal, but also provide users with 64 sets custom waveform storage space.   7. The instrument has achieved combination for ease use, excellent technical indicators and other functions in the signal generation, waveform parameter measurement and scanning and usage. It can help users to quickly complete the task and it is the test and ideal measurement equipment for electronic engineers, electronic laboratory, production line and teaching and scientific research. 8. The FY6600 Series dual channel  function/arbitrary waveform generator has the hummization keyboard layout and instructions. It provide visional intuitive operation interface. The display interface uses 2.4 inch TFT colour display. High resolution:320*240, It can display all the parameter for dual channel simultaneously and prompt present key function. 9. Abundant shortcut keys greatly simplify the complex operation process and enhance the instrument operability. Users do not need to spend a lot of time to learn and familiar with the instrument operation,you can skillfully use it. Advantages:   - FY6600 uses a professional 14Bit high-speed D/A chip, rather than a few inexpensive resistors to build a 12 bit D/A resistor network. The higher the resolution, the smoother the detail waveform. Recommend: Observe the details for two schemes of sine wave durning reducing the oscilloscope resolution range and time base.The waveform details and smoothness will immediately appear on the page. - FY6600 series sampling rate upgrades to 250MSa/s, at the same frequency, waveform contour is more clear than the 200MSa/s sampling rate instrument in the same frequency. - FY6600 series each waveform storage depth upgrades to 8192*14bits, high-precision signal details can be restored. Wave length is 4 times of friend business. - The industry original practical VCO function. - FY6600 series phase resolution can up to 0.1 degrees, the user can more accurately control the delay for two signals. - Signal output terminals uses pure copper material, not plastic wrapped zinc alloy material, the details is attitude.   - The instrument adopts imported long-life keys, and comfortable touch. - The first dual channel waveform displays in the LCD operation interface display simultaneously (non-friends imitates our 2015 version, only displays signal 1-way waveform) - 4 way TTL output makes instrument application more widely; - Small signal is particularly good,FY6600 can outputs1mVPP small signal, amplitude resolution is 1mV, and can be 1mVpp, 10mVpp, 100mVpp, 1Vpp and other different step value, the maximum range is 1mVpp~20Vpp electrodeless stepless regulation. - A wider frequency range, the maximum frequency range is 1uHz~60MHz sine wave, square wave maximum range is 1uHz~25MHz, the other wave frequency range is 1uHz~20MHz, the full range frequency resolution is 1uHz, the full range frequency shift, direct digital set; - The rising edge time is as low as 7nS within the square wave 5V, and the maximum output frequency can reach 25MHz; -Waveform types are more abundant.The instrument is not only for the user to preset 33 common waveform, also provides users with a group of up to 64 (8192*14Bit) user-defined waveform storage space.Users can use PC software provided by our company editor to download. The impulse wave width not only supports the duty ratio adjust   Specifications:   Model: FY6600 Frequency: 12/15Mhz, 30Mhz,50Mhz,60Mhz Screen display: 2.4" TFT Color: Grey Size: 194 x 178 x 69mm Packaged included:   1 x FY6600 main unit 1 x Power cable(US Plug) 1 x USB wire 1 x BNC wire 1 x CD 1 x Q9 Clip wire Detail Pictures:                       , , , , , , , , ,

ANENG Q10 Digital Multimeter 9999 Professional Tester Multimeter True RMS Analog DIY Transistor Capacitor NCV Testers Lcr Meter
ANENG Q10 Digital Multimeter 9999 Professional Tester ... $62.38

Features: ANENG Q10 is an automatic range digital multimeter with 9999 words with a true effective value. The instrument is full-key operation with triple display.Measure AC voltage and DC voltageMeasure AC and DC currentMeasuring resistance/temperatureTest continuity and diodeMeasuring capacitance/NCVMeasuring frequency and duty cycleAnti-interference AC voltage detectionSpecification: Brand ANENG Model Q10 Display (LCD) 9999 Range automatic / manual Material ABS+TPE Sampling rate 3 times/sec True RMS yes Data retention yes Screen backlight yes Low battery warning yes Automatic shut-down yes type of battery 3 * 1.5V AA battery (not included) Features Range Precision AC frequency response DC Current 9.999A/999.9mA ±(1.0%+3) - DC Current 99.99mA/9.999mA/99.99μA/999.9μA ±(0.8%+3) - AC current 9.999A/999.9mA ±(1.2%+3) 40Hz~1kHz AC current 99.99mA/9.999mA/99.99μA/999.9μA ±(1.0%+3) 40Hz~1kHz DC voltage 999.9mV/9.999V/99.99V/999.9V/9.999mV/99.99mV/999.9mV ±(0.5%+3) - AC voltage 999.9mV/9.999V/99.99V/750.0V/9.999mV/99.99mV/999.9mV ±(1.0%+3) 40Hz~1kHz Resistance 99.99Ω ±(1.0%+3) - Resistance 999.9Ω/9.999kΩ/99.99kΩ/999.9kΩ ±(0.5%+3) - Resistance 9.999MΩ ±(1.5%+3) - Resistance 99.99MΩ ±(3.0%+5) - Capacitance 9.999nF ±(5.0%+20) - Capacitance 99.99nF/999.9nF/9.999μF/99.99μF/999.9μF ±(2.0%+5) - Capacitance 9.999mF ±(5.0%+5) - Frequency 99.99Hz/999.9Hz/9.999kHz/99.99kHz/999.9kHz/5.000MHz ±(0.1%+2) - Temperature (-20~1000)℃  /  (-4~1832)℉  ±(2.5%+5)  - Duty cycle 1%~99% diode yes On and off yes NCV yes working environment temperature 0~40℃     humidity <75%   Package Includes: 1 * ANENG Q10 Digital Multimeter (Battery not included)2 * Test lead wire1 * Thermocouple1 * Manual Details Pictures:

DANIU DT832 Digital LCD Multimeter Ohm Voltage Ampere Meter Buzzer Function with Test Probe
DANIU DT832 Digital LCD Multimeter Ohm Voltage Ampere ... $17.51

Features:   DC voltage: 200mV-1000V Accuracy: ±(0.5%+2dgt) AC voltage: 200-750V Accuracy: ±(1.2%+10dgt) DC current: 2000uA-10A Accuracy: ±(1.0%+2dgt) Resistance: 200Ω-2MΩ Accuracy: ±(0.8%+2dgt) Diode test: Yes  Transistor test: Yes On-off measurement: Yes Continuity buzzer: Yes  Power supply: 9V battery 6F22 (NOT included)  Display size: Approx. 16 × 48mm/ 0.63 x 1.89" Product size: Approx. 120 × 67 × 24mm/ 4.72x2.64 x 0.94" Maximum display: 1999   Package Included:   1 x DT832  Digital Mulitmeter 2 x Test Probe Leads 1 x English User Manual Detail Pictures:                     , , , , , , , , ,

0.5Mhz-470Mhz RF Signal Generator Meter Tester for FM Radio Walkie-Talkie Debug
0.5Mhz-470Mhz RF Signal Generator Meter Tester for FM ... $145.58

0.5Mhz-470Mhz RF Signal Generator Meter Tester for FM Radio Walkie-Talkie Debug   Descriptions:   - For FM walkie-talkie debugging - Frequency 0.5M --- 470M - Signal strength -70--132dBm - Built-in 800Hz tone modulation - Use 8--12V DC power supply - Frequency 7 digits Example: 439012.5KHZ display 4390125 - Signal strength -70--132dBm effective other value is invalid - Value direct input selection item: the number keys - Numerical stepping modify the selection of project: arrow keys   Audio modulation just about 800Hz other value is invalid: F1: cycling setting item,pointing to the selected item,respectively,frequency,signal strength,audio modulation frequency F2: backspace key input of an error F3: closed,open signal output F4: closed,open audio signal modulation   >>Please Click Here to Download the English User Manual<<   Package Includes:   1 x 0.5Mhz-470Mhz RF Signal Generator Meter Tester   Detail Pictures:  

FY6900 30MHZ Dual Channel DDS Function Arbitrary Waveform Signal Generator Pulse Signal Source Frequency Counter Fully Numerical Control
FY6900 30MHZ Dual Channel DDS Function Arbitrary Wavef... $155.06

Main Features:   ♦ Adopt the Direct Digital Synthesizer (DDS) technology and provide stable, precise, pure and low distortion signals.  ♦ 2.4 inch TFT Color LCD with 320×240 resolution,  displaying parameters and graphics of the two channels at the same time. ♦ The instrument uses 14-bit high-speed D/A converter chip (5Vpp output quantization error is less than 1mV),  250MSa/s sample rate, 14bits vertical resolution. ♦  Can output up to 97 groups of functions / arbitrary waveform,  contains 33 groups of preset waveforms and 64 groups of user-defined waveforms. Preset waveforms: Sine, Square (Duty Cycle adjustable), Pulse (Pulse width and cycle time can be set accurately), Triangle/Ramp,  CMOS(0~12V), Four channels TTL , Exponential Rise, Exponential Fall, Noise, ECG, DC etc. ♦  Enable to store 64 arbitrary waveform data files, each one of waveform storage depth 8192 points * 14bits;  (The longer the waveform storage depth, the more detail the waveform is saved, and the signal details can be restored with high p'recision.) ♦ Various modulation types: AM, FM, PM, ASK, FSK and PSK modulations. ♦ Sweep Function: It can sweep 4 properties of signals including frequency, amplitude, offset and duty cycle; It has Linear and Logarithm two sweep types; 0.01S~999.99S sweep time; Up, Down and roundtrip sweep directions. ♦  VCO Function  (Voltage Control Output): Can be achieved by an external input signal: voltage controlling frequency, voltage controlling amplitude, voltage controlling offset, voltage controlling duty cycle and PWM modulations. ♦ Burst Output Function: There has Manual Trigger, internal CH2 Trigger, and External Trigger for your options. It can output 1~1048575 pulse trains. ♦ 100M Frequency meter function: It can measure frequency, period, pulse width and duty cycle. Max. frequency workable is 100MHz and Min. frequency workable is 0.01 Hz. ♦ Counter Function: It has 2 coupling measure modes including DC coupling and AC coupling. This design can solve inaccuracy problem of AC coupling. ♦ Standard dual full functional channels which are equivalent to two independent generators. ♦ Channel SYNC Function: Support waveform copy and state copy between channels. Support two or more signal generators connected to achieve multi-channel output, the maximum support 16-channel synchronous output, the phase between each channel can be adjusted. ♦ Precisely adjust the phases of the two channels, P'recision can be 0.01°. ♦ Min amplitude resolution can be up to 1 mV. Amplitude range is 0~24Vpp. ♦ Duty-cycle of each channel can be adjusted independently0.01%-99.99%,  the adjusting resolution is 0.01%. ♦ -12V~+12V DC Offset function. Resolution 0.001V. ♦ Save function: It can save 20 sets user-set parameters and can be loaded at any time. ♦ Communicating function: All functions can be controlled by PC program and the communication protocol is open for secondary development. ♦ Output short-circuit protection: All channels can work more than 60 seconds when the load is short-circuited. ♦ Provide powerful waveform editing PC software. Users can download arbitrary waveform to this instrument after edit through PC program which is included in user CD. ♦ Adopt ABS plastic shell with table type design. Use 100-240V (AC) wide range voltage power supply.  ♦ Can choose our FYA2000S series or FPA1000 series power amplifier to output 20W~100W signal in DC-10MHz width without any distortion. FY6900 can output Function/Arbitrary Waveform including: >Sine >Square >Rectangle >Triangle/Ramp >Rise Sawtooth >Fall Sawtooth >Lorenz Pulse >Multitone >Noise >Electrocardiogram (ECG) >Trapezoidal Pulse >Sinc Pulse >Narrow Pulse >Gauss White Noise >Step Triangle >Positive Step >Inverse Step >Positive Exponent   >Inverse Exponent >Positive Falling Exponent >Inverse Falling Exponent >Positive Logarithm >Inverse Logarithm >Positive Falling Logarithm >Inverse Falling Logarithm >Linear FM >AM >FM >Positive Half Wave >Negative Half Wave >Positive Half Wave   Rectification >Negative Half Wave Rectification >User-defined waveform Technical Specification: Frequency Model FY6900-20M     FY6900-30M FY6900-50M FY6900-60M Sine 0~20MHz 0~30MHz 0~50MHz 0~60MHz Square 0~15MHz 0~25MHz 0~25MHz 0~25MHz Ramp, Triangle 0~10MHz 0~10MHz 0~10MHz 0~10MHz Pulse 0~10MHz 0~10MHz 0~10MHz 0~10MHz TTL/CMOS 0 0~10MHz 0~10MHz 0~10MHz 0~10MHz Arbitrary Waveform 0~10MHz 0~10MHz 0~10MHz 0~10MHz Min pulse width 20ns(All models of pulse wave min width can be 20ns) Min. Resolution on all frequency range 1μHz (Min. resolution can low to 1μHz on all frequency range to ensure adjusting accuracy under high frequency. For example, it can output 10.000000000001MHz signal). Accuracy ±20ppm Stability ±1ppm/ 3hours Waveform Characteristics Waveforms Sine, Square, Rectangle (Duty Cycle adjustable), Pulse (Pulse width and cycle time can be set accurately), Triangle/Ramp, Sawtooth Wave, CMOS, Four channels TTL, DC, Half wave, Full wave, Positive Step, Inverse Step, Positive Exponent, Inverse Exponent, Lorenz Pulse, Multitone, Noise, ECG, Trapezoidal Pulse, Sinc Pulse, Narrow Pulse, Gauss White Noise, AM, FM, and other 64 sets customer-defined waveform. Non-Volatile Storage Can store 64 user-defined arbitrary waveforms, (8K 14bits) * 64 Waveform Length 8192 points * 14bits Sampling Rate 250MSa/s Vertical Resolution 14 bits Sine Harmonic Suppression ≥50dBc(<1MHz); ≥45dBc(1MHz~20MHz); Total Harmonic Distortion <0.5% (20Hz~20kHz,0dBm) Rectangle Rise/Fall Time ≤7ns (VPP<5V) Overshoot ≤5% Duty Cycle 0.01%~99.99% (Resolution 0.01%) Sawtooth wave Linearity >99% (0.01Hz~10kHz) Output characteristics Amplitude(VPP) Frequency≤5MHz: 1mVpp~24Vpp;5MHz<frequency≤10mhz: br="" style="box-sizing: border-box; margin: 0px; padding: 0px;"> 10MHz<frequency≤20mhz: br="" style="box-sizing: border-box; margin: 0px; padding: 0px;"> Frequency>20MHz: 1mVpp~5Vpp; Resolution 1mV Amplitude Stability ±0.5%/ 5 Hours Amplitude flatness ±2.5%(<10MHz);±5%(>10MHz); Waveform Output Impedance 50Ω±10%(Typical) Protection All channels can work more than 60 seconds when the load is short-circuited.  DC Offset Offset Range Frequency≤20MHz: ±12V;  Frequency>20MHz: ±2.5V; Offset Resolution 1mV Phase Feature   Phase range 0~359.99° Phase resolution 0.01° TTL Output   TTL Level Amplitude >3Vpp Fan-out >8 TTL LOAD Rise/Fall Time ≤10ns CMOS Output Low Electric Level <0.3V High Electric Level 1V~12V Rise/Fall Time ≤18ns External Measurement Function Frequency, Period, Positive/Negative Pulse Width, Duty Cycle Input Voltage Range 1Vpp~20Vpp Frequency Meter Resolution 0.01Hz (Gate Time = 100S) Range 0.01Hz~100MHz Sensitivity Gate Time 3 grades (1S, 10S, 100S) adjustable Counter Range 0-4294967295 Coupling DC, AC Working Mode Manual Period Measurement Range 5ns ~ 20s DC coupling measurement Pulse Width Measurement Range 0ns ~ 20s Resolution 5ns Duty Cycle Range (Display) 0% ~ 100% Sweep Carrier Waveform Sine, Square, Ramp, Arbitrary (except DC) Sweep Type Linear or Logarithm Sweep Direction Up, Down and roundtrip sweep directions; Sweep Objects Frequency, Amplitude, Offset, Duty Cycle Sweep Time 0.01S~999.99S/Step Setting range Starting position and Finishing position can be set arbitrarily. Sweep Range Decided by Parameters setting. VCO (Voltage Control Output) Modulation signal range to input 0~5V VCO signal frequency range 0-2000Hz VCO control object voltage controlling frequency (VCF), voltage controlling amplitude , voltage controlling offset, voltage controlling duty cycle. VCO special function Can Amplitude Modulate (AM) or Frequency Modulate (FM) by external analog signal. Modulation Modulation Type AM, FM, PM, ASK, FSK, PSK Carrier Waveform Sine, Square, Triangle, Ramp, Arbitrary waveform (Except DC) AM Source Internal (CH2) / External (VCO IN Port) Modulating Waveform Sine, Square, Triangle, Ramp, Arbitrary waveform Depth 0% to 120% Modulating Frequency Internal : 1μHz~1MHz;  External: 1μHz~2KHz; FM Source Internal (CH2) / External (VCO IN Port) Modulating Waveform Sine, Square, Triangle, Ramp, Arbitrary waveform Modulating Frequency Internal : 1μHz~1MHz;  External: 1μHz~2KHz; PM Source Internal (CH2) / External (VCO IN Port) Modulating Waveform Sine, Square, Triangle, Ramp, Arbitrary waveform Phase Deviation 0° to 360° Modulating Frequency Internal : 1μHz~1MHz;  External: 1μHz~2KHz; ASK Source Internal (CH2), External (ASK IN Port), Manual Modulating Waveform Square with 50% duty cycle. Key Frequency 1μHz~10MHz FSK Source Internal (CH2), External (FSK IN Port), Manual Modulating Waveform Square with 50% duty cycle. Key Frequency 1μHz~10MHz PSK Source Internal (CH2), External (PSK IN Port), Manual Modulating Waveform Square with 50% duty cycle. Key Frequency 1μHz~10MHz Burst Function Carrier Waveform Sine, Square, Ramp, Arbitrary (except DC) Burst Count 1~1048575 Trigger Source Manual, Internal, External (AC/DC) General Specifications Display Type 2.4 inch, TFT Color Display. Save & Load Amount 20 Position 01 to 20 (01 for start default value) Interface Type USB to Serial interface Protocol C'ommand line mode, providing communication protocols. Communicating Speed 9600bps (Industrial standard) Power Voltage Range AC100V~240V Technic SMD, LSI, Reliable and durable Buzzer Can be turned on/off by setting. Operation Buttons and knob continuously. Environment Temp.: 0~40℃, Humidity:<80% Size 200mm * 190mm * 90mm (L * W * H) Weight 850g Package Size 25cm * 21cm * 10cm (L * W * H) Package Weight 0.98kg(Main engine, accessories and packing materials) Note: FY6900 supports English & Chinese  menu switch. The defaul language is English.  >>Please Click Here to Download the English User Manual<< Package Includes: 1 x 30MHz FY6900 DDS Signal Generator 1 x Power Cable 1 x USB Data Cable  2 x BNC-Clip Cables 1 x BNC-BNC Cable Details Pictures:

FY107B/FY107C Smart Automatic Digital Multimeter 6000 Counts High Precision Small Portable Anti-burning Universal Meter
FY107B/FY107C Smart Automatic Digital Multimeter 6000 ... from $36.30

Features:  Smart anti-burning, automatic identification of the measured object and realization of 250V voltage intelligent anti-burning. It can be automatically identified or switched manually. Automatic identification: AC and DC voltage frequency resistance on-off buzzer. Manual switching: AC and DC voltage frequency on and off, buzzer, capacitor, diode, temperature, live wire identification NCV. 3.3-inch large screen high-definition display, using high-definition LCD color large screen. The body is made of ABS material, weight: about 146g, size: 142x70x20mm. Live wire recognition, the single test lead is inserted into the socket to judge. NCV three-color analog bar, NCV non-contact voltage detection, high-sensitivity voltage probe, the screen displays the signal strength, the closer to the power supply, the faster the alarm sound. Specification: AC voltage 10mV~ 750V ±(1.2% rdg+3) DC voltage 10mV~ 1000V ±(1.2% rdg+3) Resistance 50Ω~60MΩ ±(2% rdg+5) Frequency 10HZ~6MHZ ±(0.1% rdg+3) Capacitance 10nf~9999uf ±(4.5% rdg+5)   Temperature (FY107C only) -20°C~0°C ±(5% rdg+4) - 1°C~400°C ±(1% rdg+3) -401°C~ 1000°C ±(2% rdg) On-off beep The resistance is lower than 500 buzzer sounds Diode Display the approximate value of diode forward voltage drop NCV voltage detection There are three alarm methods according to the distance of the power supply Live wire neutral wire Live wire display LIVE accompanied by alarm sound, neutral wire no response Automatic shut-down Automatic shutdown after about 15 minutes without operation Size 142x70x20mm Test lead Can be replaced at will Battery Two AAA 1.5V batteries (not included) Package includes: 1 x Multimeter 1 x Product packaging box 1 x Cloth bag 1 x User manual 1 x Temperature Probe(only for FY107C) Details pictures: 

ANENG V05B Digital True RMS bluetooth 6000 Counts Professional Analog Multimeter AC/DC Currents Voltage Mini Testers Multimetro
ANENG V05B Digital True RMS bluetooth 6000 Counts Prof... $44.13

Description: Package included: 1 * V05B multimeter With Test Leads (battery is not include)1 * Packing Box1 * User Manual Details pictures: 

ANENG AN888S Digital 4 1/2 19999 High-Precision True RMS Multimeter + bluetooth Speaker + Clock + Temperature Display Profesional Multitester with Ohm Meter Tester Standard Version
ANENG AN888S Digital 4 1/2 19999 High-Precision True R... from $130.86

>>Please Click Here to Download the English User Manual<< Feature: This product is an automatic range multi-function digital multimeter with 19999 word high precision display. The meter is driven by a lithium battery, with true rms measurement, LCD display, adjustable backlight brightness, clear reading, clock, alarm clock, bluetooth audio, ambient temperature display. Specifications: Display (LCD)  19999 COUNT  Range  automatic / manual  Material  ABS+TPE  Sampling rate  3 times / sec  True RMS  √  Data retention  √  Screen backlight  √  Low battery prompt  √  Automatic standby  √  type of battery  18650 lithium battery  Features  Range  Precision  DC voltage (V)  1.9999V/19.999V/19.999V/1000.0V  ±(0.05%+3)  DC voltage (mV)  19.999mV/199.99mV  ±(0.05%+3)  AC voltage (V)  1.9999V/19.999V/199.99V/750.0V  ±(0.3%+3  AC voltage (mV)  19.999mV/199.99mV  ±(0.3%+3  DC (A)  1.9999A/19.999A  ±(0.5%+3)  DC (mA)  19.999mA/199.99mA  ±(0.5%+3)  AC (A)  1.9999A/19.999A  ±(0.8%+3)  AC (mA)  19.999mA/199.99mA  ±(0.8%+3)  Resistance (Ω)  199.99Ω  ±(0.5%+3)  Resistance (KΩ)  1.9999kΩ/19.999kΩ/199.99kΩ  ±(0.2%+3)  Resistance (MΩ)  1.9999MΩ/19.999MΩ  ±(1.0%+3)  Resistance (MΩ)  199.99MΩ  ±(5.0%+5)  capacitance  9.999nF  ±(5.0%+20)  capacitance  99.99nF/999.9nF/9.999μF/99.99μF/999.9μF  ±(2.0%+5)  capacitance  9.999mF  ±(5.0%+5)  frequency  99.99Hz/999.9Hz/9.999kHz/99.99kHz/999.9kHz/6.000MHz  ±(0.1%+2)  diode  YES    On and off  YES     bluetooth version  V5.0  Transmission distance  ≤10M  rated power   2 x 4W RMS  Frequency response range    100Hz-18KHz  Distortion  ≤1%  Signal to noise ratio  ≥76dB Package includes: 1 x Digital Multimeter 1 x Test leads  1 x English User Manual >>>Want to find ANENG AN888S Digital Multimeteter + 18 in 1 Combination Lines Version ,pleases click here Details Pictures:

FLUKE F101 600V CATⅢ Pocket Digital Multimeter Auto Range
FLUKE F101 600V CATⅢ Pocket Digital Multimeter Auto Range $112.40

Description :  FLUKE F101 600V CAT Ⅲ Pocket Mini Digital Multimeter Auto Range  Widely used for testing resistance, on/off, diode, capacitor, frequency and voltage, AC/DC voltage can be up to 600V, basic DC accuracy is 0.5%, this is indeed a professional and preferred digital multimer for the elecrical people.   Specification : Brand Name :  FLUKE Model Number : F101 Maximum input voltage 600V LCD Display 6000 words refresh rate 3/second  Power supply 2 AAA, NEDA 24A, IEC LR03 Battery life More than 200 hours Operating temperature 0 °C to 40 °C Storage Temperature -30 °C to 60 °C Operating relative humidity Non-condensing 10 °C  90% at 10 °C to 30 °C; 75% at 30 °C to 40 °C Operating relative humidity range 40M 80% at 10 °C to 30 °C; 70% at 30 °C to 40 °C (Without Consideration) Operating altitude 2000 m Storage altitude 12,000 m Temperature Coefficient 0.1 x (specified accuracy)/°C or/u003c18 °C or/u003e 28 °C Dimensions (H*W*L) 130 mm x 65 mm x 27mm Weight 160 g IP Rating IEC 60529 : IP 40 Security Level IEC 61010-1 : 600 V CAT III, Pollution Degree 2 Electromagnetic interference IEC 61326-1 : Class handheld   Reference parameter :  Function Range Resolution Accuracy +/- % of(reading + minimum resolution) AC voltage v(40Hz-500Hz) 6.000V 0.001V 1% +3 60.00V 0.01V   600.0V 0.1V   DC voltage 6.000V 0.001V 0.5% +3 60.00V 0.01V   600.0V 0.1V   AC millivolt 600.0 mV 0.1mV 3% +3 Diode test 2.000V 0.001V 10% Resistance 400.0  0.1  0.5% + 3 4.000 k 0.001 k 0.5% + 2 40.00 k 0.01 k 0.5% + 2 400.0 k 0.1 k 0.5% + 2 4.000 M 0.001 M 0.5% + 2 40.00 M 0.01 M 1.5% + 3 Capacitance 50.00 nF 0.01 nF 2% + 5 500.0 nF 0.1 nF 2% + 5 5.000 F 0.001 F 5% + 5 50.00 F 0.01 F 5% + 5 500.0 F 0.1 F 5% + 5 1000 F 1 F 5% + 5 Frequency(10Hz-100KHz) 50.00 Hz 0.01 Hz 0.1% + 3 500.0 Hz 0.1 Hz   5.000 kHz 0.001 kHz   50.00 kHz 0.01 kHz   100.0 kHz 0.1 kHz   Duty Cycle 1% -99 % 0.1% 1% typ Package Includes :  1 x FLUKE F101 Professional Digital Multimeter 1 x Red And Black Test Leads 1 x English User  Mannul ~~~CLICK TO DOWNLOAD~~~ NOTE: The logo of FLUKE is Chinese~   Details Pictures :     , , , , , ,

ANENG ST206 Digital Multimeter Clamp Meter 6000 Counts True RMS Amp DC/AC Current Clamp Tester Meters Voltmeter
ANENG ST206 Digital Multimeter Clamp Meter 6000 Counts... $51.63

Support AC Current,AC Voltage,DC Current,DC Voltage Measurement Features:   1. Display: liquid crystal display (LCD); 2. Maximum display: 4000 (3 3/4) bit automatic polarity display; 3. Measurement method: double integral A/D conversion; 4. Sampling rate: about 3 times per second; 5. Over range display: The highest position shows “OL”; 6. Low voltage display:symbol appears; 7. Working environment:(0~40)°,relative humidity<80%; 8. Power: AAA 1.5V battery (Batteries excluded) 9. Volume (size): 165×64.5×31mm (L×W×H);    Specifications:   DC voltage (DCV):4V-40V-400V-600V  ±(0.5%+3) AC voltage (ACV): 4V-40V-400V-600V ±(1%+3) AC current(ACA):4A-40A-400A-600A ±(2.5%+8) DC current(DCA):60A-600A ±(2.5%+30) Resistance: 4kΩ-40'kΩ-400kΩ-4MΩ-40MΩ  ±(0.5%+3) Frequency measurement: 4Hz-40Hz-400Hz-4kHz-40,kHz-400kHz-1MHz ±(0.1%+2) Capacitance measurement:4nF-40nF-400nF-4μF-40μF-400μF-4mF ±(2%+5) Temperature measurement : -30~1000° / 22~1832° ±(2.5%+5)   Package Includes:   1 * Instruction Manual 1 *  Multimeter 1 * Pair of test leads 1 * Temperature probe 1 * Storage Bag   Details Pictures:

HYELEC PEAKMETER MS2108 Digital Clamp Tester Inrush Current True Rms Ohm Meter Clamp Meter Backlight
HYELEC PEAKMETER MS2108 Digital Clamp Tester Inrush Cu... $99.73

Description : HYELEC MS2108 Digital Clamp tester Inrush Current True RMS Ohmmeter Clamp Meter Backlight This meter is a portable professional measuring instrument with LCD and back light easily reading. The ‘single-hand operation’ design for the range switch makes measurement simple and easy. Overload protection and low battery indication are provided. It is an ideal multi-function Instrument with scores of practical applications for professional, workshop, school, hobby and home use. Features :   1.The meter can perform measurements of AC/DC voltage and current, resistance,frequency, duty, capacitance, as well as continuity and diode test. 2.Both auto range and manual range are available. 3. This meter is equipped with reading hold function. 4. This meter is equipped with true root mean square value measuring function (at AC A and AC V range). 5. This meter is equipped with inrush current measuring function. 6. This meter is equipped with auto zero function (at DCA range). 7. This meter is equipped with maximum value measuring function. 8. This meter is equipped with minimum value measuring function. 9. This meter can measure frequency by clamp.   Specifications :   DC Voltage : 660mV/6.6V/66V±(0.8%+3)  660V±(1.0%+5) AC Voltage : 660mV/6.6V/66V/660V±(1.5%+5)   AC Current : 66A/600A±(3.0%+10) DC Current : 66A/600A±(3.0%+10) INRUSH CURRENT(100ms) : 66A/600A±(10.0%+60) Resistance : 660Ω/6.6kΩ/66k?/660kΩ/6.6MΩ±(1.2%+2)  66MΩ±(2.0%+5) Capacitance : 6.6μF/66μF/660μF/6.6mF/66mF±(4.0%+3) Frequency : 10kHz±(1.5%+5) Duty cycle : 10%~95%±(3.0%+2) Package size : 23 x 11 x 6cm / 9.2 x 4.4 x 2.4in Package weight : 465g / 1lb   Package included :    1 x HYELEC MS2108 Digital Clamp Meter 2 x Test Cable 1 x English Manual 1 x Portable Bag Good News: The logo of HYELEC will be upgraded to PEAKMETER on March 1, 2016. Even though the logo will be upgraded, after-sales service won't be affected, including HYELEC and PEAKMETER. Details pictures :      

FY3224S (FY3200S-24M) 24MHz Dual-channel Arbitrary Waveform DDS Function Signal Generator Sine Square Wave Sweep Counter
FY3224S (FY3200S-24M) 24MHz Dual-channel Arbitrary Wav... $108.99

Description:   FY3224S 24MHz Dual-channel Arbitrary Waveform DDS Function Signal Generator Sine Square Wave Sweep Counter   Features:    Output signal frequency high accuracy, good stability. Signal amplitude up to 20Vpp. Instrument can realize the adjustment program of function parameters , easy to use. Accompanying frequency meter, counter function, high cost. The instrument can output sine, square, triangle, ramp, pulse, staircase, DC voltage waveform. Pulse wave pulse width precision can be adjustable.   Function: 1. Using DDS direct digital synthesis technology to generate precise, stable, low distortion output signal. 2. CH1 and CH2 completely symmetrical two channels, each channel can be independently set the parameters. 3. Supports user-defined waveforms, each arbitrary waveform memory depth 2048 x 12bits, 250MSa / s sampling rate. 4. Has burst burst output, selectable manual trigger, internal and external trigger CH2 trigger three trigger modes that allow the unit to any output 1 - 1048575 bursts. 5. Measurement functions: instrument comes with 100MHz frequency counter functions and pulse counter functions. 6. Waveform generator up to 12 bits wide, the output waveform is more delicate, waveform distortion is reduced magnitude. 7. With full CNC functions, display and digital adjustment phase current amplitude of the output signal, offset, frequency, duty cycle, and the two signals. 8. After connecting the instrument to the computer, you can use the computer through the PC control signal generator functions and parameters, and can be edited on a computer to download arbitrary waveform output waveform to the instrument. 9. Communication: serial communication, protocol completely open, user-friendly secondary development. 10. High frequency accuracy: frequency accuracy up to 10-6 magnitude. 11. High frequency resolution: the full range of frequency resolution 10mHz. 12. Tracking function: built-in frequency, amplitude, offset, duty cycle, waveform and other parameters follow function, easy to use. 13. Scanning features: a frequency linear sweep and logarithmic sweep function, scan start and end points can be set. 14. Storage feature: You can store 20 groups instrument state parameters set by the user, can be called up to Reproduce 15. Operation: key operation, LCD1602 LCD display in English, direct digital setting parameters or continuous adjustment knob. 16. Input voltage protection: extended power input range AC85V to AC240V wide voltage. 17. Output short circuit protection: All signal outputs can operate at over load short circuit 60S.         Technical Parameters: Built-in switching power supply: AC85V-AC260V Interface: USB Signal output: Output amplitude: ≥≥20Vp-p (no load) Output Impedance: 50Ω ± 10% DC polarization: ± 10V Frequency range: 0Hz - 24MHz (orther  0Hz - 6MHz) Counter: Count range: 0-4294967295              Measurement frequency range: 1Hz - 100MHz Input amplitude: 1Vp-p - 20Vp-p Scan function: Scanning mode: Linear sweep, logarithm scanning Frequency Range: Start and end points set arbitrary Frequency scanning range: M1 - M2 predetermined frequency Scan rate: 1s ~ 999s / step Other: Storage and transferred functions: M0 - M9 (M0: default) Size: 200mm (L) × 190mm(W) × 90mm(H) Beeper function: to set open or closed by the program Operating characteristics: All key operation, continuous adjustment knob Environmental conditions: Temperature 0 - 40 ℃ humidity <80% >>>CLICK HERE to download all the files in the CD<<< >>>CLICK here to download the user manual<<<   Package includes:    1 x FY3224S 24MHz Dual Channel DDS Function Signal Generator 1 x 1M power cable 1 x 1.25M USB cable 2 x 1.1M Q9 cables Note:It is US plug type,will send a plug adapter according to you country. Details pictures:                     

HoldPeak Digital Clamp Multimeter HP-570C-APP 1000A AC/DC Current Voltage Temperature Meter Link to Phone APP to Recored Data
HoldPeak Digital Clamp Multimeter HP-570C-APP 1000A AC... $92.62

Note: Two shells are shipped randomly Descriptions: Auto ranging clamp multimeter with AC/DC current, AC/DC voltage, resistance, capacitance, temperature, frequency, diode and continuity test. Jaw opening measures AC current in a conductor up to 45mm without interrupting the circuit. Features Data Hold, Max/Min Reading, Backlight, an easy-to-read large LCD. Comes with a handy carrying pouch - Perfect for use while on the go. The mobile phone can be connected to the HP-570C-APP Clamp Meter through the APP to read and operate on the mobile phone. This design is convenient and advanced. Specifications: Brand Name:HoldPeak Display Type:Digital Only Measuring Capacitance Range:5.12nF/51.2nF/512nF/5.12uF/51.2uF/100uF Measuring Current Range:200A/400A/0-800A/800-1000A Measuring Resistance Range:400/4k/40k/400k/4M/40M Weight:450g Operating Temperature:-20~1000'C Dimensions:225*97*40mm Model Number:HP-570C-APP DIY Supplies:Electrical Measuring Voltage Range:400mV/4V/40V/400V/750V/1000V Measuring Frequnency Range:5.12Hz/51.2Hz/512Hz/5.12kHz/512kHz/5.12MHz Display:4000 Diode Test:YES Continuity Buzzer:YES Date Hold/Back Light:YES Auto Power Off:YES Relative Value:YES Dual Display:YES Link to phone App:YES Battery Type:9V(6F220)*1(Not Included) Package Included: 1 x HoldPeak 570C-APP Clamp Meters (Battery Not Included) 1 x Test Lead 1 x English Manual Detail Pictures:

ANENG XL830L Digital LCD Multimeter Voltmeter Ammeter AC/DC/OHM Volt Current Tester
ANENG XL830L Digital LCD Multimeter Voltmeter Ammeter ... $15.10

Features:   This Heavy-Duty general purpose multimeter features a Clear, easy to read LCD display, with blue back Light. Overload Protection on all ranges. Housed in a rugged rubber boot with integral stand. Low Battery Voltage Indication. Portable & Compact Design. Data Hold Function & Diode Test Facility. 20 Position Rotary Switch. Measures AC & DC Voltage, DC Current, Resistance, Audible Continuity, Diode/Transistor Verification Mode. Specification: DC Voltage: 200mV 2V 20V 200V 600V AC Voltage: 200V / 100mV, 600V / 1V DC Current: 200μA 2mA 20mA 200mA 10A Resistance: 200Ω 2kΩ 20kΩ 200kΩ 2MΩ Transistor hFE Test: NPN & PNP 0~1000 1b=10mA Vce=3V   Package included:   1 x ANENG XL830L Digital LCD Multimeter (Battery is not included) 2 x Test Probe 1 x English User Manual Detail Pictures:  

ANENG AN870 Auto Range Digital Precision Multimeter 19999 Counts True-RMS NCV Ohmmeter AC/DC Voltage Ammeter Transistor Tester
ANENG AN870 Auto Range Digital Precision Multimeter 19... $69.39

Click The Link To Find Green Version:   https://www.banggood.com/ANENG-AN870-Auto-Range-Digital-Multimeter-19999-Counts-True-RMS-NCV-ACDC-Voltage-Green-p-1329989.html?cur_warehouse=CN This product is a battery-powered, true-rms, auto-ranging digital multimeter with a 19999 LCD display and a backlight. click here to download the user manual    Features:  Brand Name: ANENG  Model Number: AN870  Operating Mode:Auto/Manual Ranging  Measuring Current Range:(199.99-1999.9)uA/(19.999-199.99)mA/1.9999-199.99uA  Measuring Voltage Range:19.999mV/199.99mV/1.9999V/19.999V/199.99V/750ACV(1000DCV)  Measuring Inductance Range:no  Display Type:Digital Display  Measuring Capacitance Range:9.999nF/99.99nF/999.9nF/9.999uF/99.99uF/999.9uF/9.999MF  Measuring Resistance Range:199.99/1.9999K/19.999k/199.99k/1.9999M/19.999M/199.99M  Frequency:99.99Hz/999.9Hz/9.999KHz/99.99KHz/999.9KHz/9.999MHz  Temperature:-20~1000℃/-4~1832℉ Diode Test:Yes  Duty Cycle:1%-99%  Continuity:Yes  NCV:Yes  Auto-Power Off:Yes  Battery Type:2*1.5V AA (not included)  Dimensions: Approx 180x90x45 mm  Operating Temperature:0 - 40 ℃    Package Includes:    1 x Multimeter  1 x Test lead+temperature sensor 1 x User Manual 1 x Storage bag 16pc Test probe   Details Pictures:  , , , , , , , , ,

HT206A/HT206B/HT206D AC/DC Digital Clamp Meter for Measuring AC/DC Voltage , AC/DC Current, NCV Clamp Multimeter
HT206A/HT206B/HT206D AC/DC Digital Clamp Meter for Mea... from $43.58

Description: The new generation of high-performance digital clamp meter makes your work easier, more efficient and safer. Measurable AC/DC voltage, AC/DC current, frequency, duty cycle, resistance, temperature, diode, continuity, NCV, etc. Features:  --Made of high-quality materials, it is durable, very practical, wear-resistant and stable in performance. --It features hold result and max value buttons that makes it quicker and easier to use. --A two-wire display that displays AC voltage/current and frequency or Celsius and Fahrenheit on the screen. --LCD Display: Ultra-clear display, clear reading, easy to read the values when you operate. --Hold and backlight button:The data hold button and backlight button are on the side of the meter. A short press will hold the data for you, and a long press will turn the backlight on. It is convenient for one-handed operation when measuring. --Avoid hazardous situations by using the convenient clamp to safely measure AC currents without having to strip a cord or break a circuit. --Auto power off: no operation in 15 minutes. The instrument will shut down automatically to save battery energy.  --Multifunctional: Accurate AC/DC voltage, AC/DC current, frequency, duty cycle, capacitance, resistance, temperature, diode, continuity, NCV, etc. --Wide range of applications, ideal for home and professional use, automotive, home and industrial electrical troubleshooting. Specifications:  Brand Name: HABOTEST Color: Red Model: HT206A/HT206B/HT206D(optional) Material: ABS Display: LCD Display Jaw Opening: 25cm DC voltage: 600mV/6V/60V/600V(±0.5%reading+5) AC voltage: 6V/60V/600V(±1.0%reading+5) AC current: 6A/60A/600A(±2.5%reading+8) Resistance: 600Ω/6KΩ/60KΩ/600KΩ/6MΩ/60MΩ(±1.0%reading+5) Duty cycle: 1-99% Frequency (Hz): 10Hz~10MHZ  Maximum count: 6000 Temperature: -40~1000℃ / -40~1832℉ Power Supply: 2x 1.5V AAA Batteries (Not Included) Operating Temperature & Humidity: 0-40℃ (<80%RH ,<0℃ non-condensing) Storage Temperature & Humidit: -10-60℃ (<70%RH,remove the battery) MAX.Voltage between terminals and earth ground: 600V Over range indication: it displays "OL" Continuity: orange backlight on Type: HT206A Item weight: 190g/0.418lb Item size: 19.3x7.3x3.4cm / 7.6x2.9x1.3in Package weight: 377g/0.83lb Package size: 22.5x11.5x4.5cm/8.86x4.53x1.77in HT206B Item weight: 191g/0.42lb Item size: 19.3x7.3x3.4cm / 7.6x2.9x1.3in Package weight: 392g/0.86lb Package size: 22.5x11.5x4.5cm/8.86x4.53x1.77in HT206D Item weight: 194g/0.43lb Item size: 19.3x7.3x3.4cm / 7.6x2.9x1.3in Package weight: 395g/0.87lb Package size: 22.5x11.5x4.5cm/8.86x4.53x1.77in Package includes: 1 x Digital clamp meter 1 x User Manual(English) 1 x Pair of Test Leads 1 x Temperature Probe Details Pictures:  

Borbede 168B Digital Multimeter 6000 Count DC AC Capacitance Resistance Temperature Mini Tester
Borbede 168B Digital Multimeter 6000 Count DC AC Capac... $35.68

Description:   Borbede 168B Digital Multimeter is a pocket-sized 3 5/6-bit automatic digital instrument. It has stable performance, high precision, high reliability, clear readings, and overload protection. This instrument can measure the DC/AC voltage and current, resistance, capacitance, diode, temperature, continuity test, NCV, frequency and true RMS and other parameters. Special Screen dust cover design, practical and beautiful. With AAA 1.5Vbattery-driven, the instrument uses a large-screen LCD display, boost power supply, even in the 2.3V low battery edge, it can guarantee the backlight high brightness. It's portable and handheld, measuring just 145 x 70 x 30 mm and 200g(with battery), is a ideal tool for the laboratory, factory, radio enthusiasts and families.   Features:   Display: liquid crystal display (LCD) Maximum display: 5999 (5 5/6) bits Automatic polarity display Working environment: (0 ~ 40)℃relative humidity < 80% Power supply: 2 * 1.5V AAA battery (not included) Volume (size): 145×70×30mm Weight: 200g(with battery)   Specification:   Basic function: DC Voltage: 6V/60V/600V/1000V AC Voltage: 6V/60V/600V/750V DC Current: 600uA/6000uA/60mA/600mA/10A AC Current: 600uA/6000uA/60mA/600mA/10A Resistance: 600Ω/6kΩ/60kΩ/600kΩ/6MΩ/40MΩ Capacitance: 60nF/600nF/6uF/60uF/600uF/6mF/30mF Frequency: 10Hz-20MHz Duty Cycle: 0.1%-99% Special function: Diode Test, Continuity Test, Automatic shutdown, Input impedance, Continuity Buzzer, NCV, True RMS Measurement, Temperature, Average Measurement, Date Hold, LCD Backlight, Low battery tips, Flashlight... Temperature: (-20 - 1000)℃/(0 - 1832)F   Packing Included:   1 x Multimeter 1 x A pair of pen 1 x Temperature probe 1 x English User Manual 1 x Box Details Pictures:

ANENG Q1 9999 Counts True RMS Digital Multimeter AC DC Voltage Current Tester Orange Yellow
ANENG Q1 9999 Counts True RMS Digital Multimeter AC DC... $69.73

Features:   1. True RMS 2. NCV 3. Auto and manual ranges selectable 4. Analog bar graph 5. Black EBTN screen   Specifications:   Capacitance: 9.99nF/99.99nF/999.9nF/9.99uF/99.99uF/999.9uF/9.999MF Voltage: 999.9mV/9.999V/99.99V/999.9V Current: 999.9uA/99.99uA/999.9mA/10A Resistance: 99.99/999.9/9.999k/99.99k/999.9K/9.999M/99.99M Ohm Frequency: 99.99Hz/999.9Hz/9.999KHz/99.99KHz/999.9KHz/5MHz Temperature:  -20℃~1000℃/-4℉-1832℉     Display Type: Digital Display Diode Test: Yes Continuity: Yes Duty Cycle: 1%-99% Sample Rate: 3 times per second Power: 2 x 1.5V AA batteries(Not Included) DIY Supplies: Electrical Operating Mode: Auto/Manual Ranging Operating Temperature: 0 - 40 ℃ Operating Humidity: ≤75%RH Storage Condition: -20~60℃ Storage Humidity: ≤80%RH   Package Included:   1 x ANENG Q1 9999 Counts True RMS Digital Multimeter 1 x 16 in 1 Multifunctional Test Line  2 x Test Probe 1 x Temperature Sensor 1 x Storage Bag 1 x English User Manual   Detail Pictures:  

ANENG PT1028 1000V 22 In 1 Multi-function multimeter leads Combination Test Cable Universal Meter Test multimeter pen multimetro
ANENG PT1028 1000V 22 In 1 Multi-function multimeter l... $28.61

Description: Quantity: 1set (22pc) Color: Black / Red /Silver Material: Silicone / metal Specifications: Red: positive Black: negative Cable Length:90cm/35" 1. Easy to read: "+" & "-" signs near probes 2. With rubber shrouded, it is comfortable to grip 3. Universal multi-meter plug, convenient to use 4. It is one of the useful tools that will brings a lot of convenience for your electronic work Package includes: 2 x Silicone wire test pen 2 x Extended nicke-plated copper needle 2 x Nickel-plated copper needle 2 x Tapered needle 2 x Banana tip 2 x Banana plug 2 x Alligator clip 2 x U-shaped insert 2 x Injection sheath needle 4 x Gold-plated extra tip Details picture:

Auto RF Modulator Compact RF Modulator Audio Video TV Converter RHF UHF Signal Amplifier AC230V
Auto RF Modulator Compact RF Modulator Audio Video TV ... $61.20

Features: Humanized design, easy to install and operate. High performance circuit design provides accurate picture reproduction. Can convert audio and video to RF via channel.  VHF / UHF operating frequency from 47 to 868 MHz. With selectable output level of audio and video. Compatible with all local CATV system.   Specification: Plug Type: US / EU / AU(Optional) Color: Blue Material: ABS Input: AC230V/110V, 50Hz Max. Power: 3W Frequency Range: 47-868MHz Output Impedance: 750Hm Output Level: 80-95dBuV Input Level: 0.77Vp-p for 80%+/-10% modulation Sound System: M=4.5MHz , B/G=5.5MHz , I=6.0MHz , D/K=6.5MHz A/V connector: RCA Female RF Input: F Female RF Output: F Female Operating Temperature: -10℃ ~+60℃ / 14℉~140℉ Item Size: Approx. 15.5 * 8.6 * 5cm / 6.1 * 3.4 * 2in  Item Weight: Approx. 356g / 12.6oz Package Size: Approx. 16.5 * 10.8 * 5.5cm / 6.5 * 4.3 * 2.2in  Package Weight: Approx. 415g / 14.6oz   Package Included: 1 x Modulator 1 x User Manual(English)   Details Pictures:

188
Afterpay American Express Apple Pay Bitcoin Dankort Diners Club Discover Dogecoin Dwolla Forbrugsforeningen Google Pay iDEAL JCB Klarna Litecoin Maestro Mastercard PayPal Shop Pay SOFORT Visa